Strength and elongation of spray formed Al-Si-Pb alloys

Tomar, Aruna; Mittal, R.; Singh, Devendra

doi:10.1007/s12613-014-1030-6

Cited by 7 publications

(3 citation statements)

References 21 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Accordingly, several works are being performed taking lead and graphite reinforcement to Al-Si alloys. [3][4][5][6][7][8][9][10][11] Commonly, it is observed that mixing of Pb and graphite have severe effect on the properties of Al-alloys such as, ductility, formability, and thermal conductivity. However, due to wide liquid immiscibility gap over different composition and over range of temperature selection with large density difference of Al and Pb, early techniques are not suitable for casting these alloys.…”

Section: Doi: 101002/masy202300064mentioning

confidence: 99%

Perspectives on Tribological Properties of Spray Formed Al–Pb Alloys

Singh,

Mittal

2024

Macromolecular Symposia

Self Cite

View full text Add to dashboard Cite

This article addresses the tribological characteristics and the influence of mechanical work on the porosity of spray formed Al–Si–Pb alloys. Al‐alloys are extensively utilized in industry due to their self‐lubricant qualities, particularly in the bearing company. In the case of immiscible alloys, the spray approach is the most convenient way to adopt since it allows for single‐step fabrication. The spray process has a high cooling rate, which affects the microstructure of alloys and results in equiaxed grain morphology. Spray deposition and several factors affecting to it are discussed here. This study examines the effect of secondary processes such as cold rolling, hot rolling, extrusion, and so on on porosity, hardness, tensile strength, and tribological behavior. A comprehensive knowledge of the principles of spray techniques and their respective influence on tribological properties are discussed in this perspective by comparing the available literatures, and a future scope for better development is emphasized.

show abstract

Section: Doi: 101002/masy202300064mentioning

confidence: 99%

Perspectives on Tribological Properties of Spray Formed Al–Pb Alloys

Singh,

Mittal

2024

Macromolecular Symposia

Self Cite

View full text Add to dashboard Cite

show abstract

“…Tomar et al [58] investigated about the mechanical properties of Spray formed Al-Si-Pb alloys. It was found that the ultimate tensile strength, proof stress and elongation to fracture decrease linearly and exponentially with increase in the lead content and porosity of the deposit respectively.…”

Section: Mechanical Behaviour Of the Spray Deposited Al-alloysmentioning

confidence: 99%

“…Al-alloys are extensively used in the assorted applications like aerospace, electrical, automotive [1,2], pulleys, bearing materials [3], and electronic industries [4] due to its excellent physical, chemical and thermal properties like low weight, superior wear and corrosion resistance, ease of casting, and lower thermal coefficient values [5,6]. This pa-per is mainly focused on the Al, Si and Pb based alloys due to specific usage in bearing material application.…”

Section: Introductionmentioning

confidence: 99%

Characterization of spray formed Al-alloys — A Review

Reddy

Maity

Pandey

2019

Reviews on Advanced Materials Science

View full text Add to dashboard Cite

A review on the characterization of mechanical, metallurgical, porosity, tribological and corrosion properties of spray deposited Al-alloys are presented in this paper. Al-alloys are potentially used in various applications specifically in bearing materials, aerospace due to low weight to high strength, proper lubrication, excellent wear and corrosion resistance. Al alloys being processed through spray forming technology, which possesses lower processing steps than the other conventional methods like ingot and powder metallurgy. Characterization of Al alloys spray deposits is carried out before and after mechanical processes to know their behaviour. Reviewed the characterization deportment of Al-alloys before and after spray deposition, effect of mechanical process like cold rolling, extrusion, aging, hot rolling, hot extrusion etc. and porosity on the metallurgical, hardness, tensile strength, elongation, tribological and corrosion properties.

show abstract

Studying the Influence of Rolling Deformation Degree and Pb Content on the Hardness of Spray Deposited Al–6Si Alloy Using Linear Regression Analysis

Mittal

Reddy²

2021

Powder Metall Met Ceram

View full text Add to dashboard Cite

Strength and elongation of spray formed Al-Si-Pb alloys

Cited by 7 publications

References 21 publications

Perspectives on Tribological Properties of Spray Formed Al–Pb Alloys

Perspectives on Tribological Properties of Spray Formed Al–Pb Alloys

Characterization of spray formed Al-alloys — A Review

Studying the Influence of Rolling Deformation Degree and Pb Content on the Hardness of Spray Deposited Al–6Si Alloy Using Linear Regression Analysis

Contact Info

Product

Resources

About