Structural Features and Corrosion Resistance of Fe66Cr10Nb5B19 Metallic Glass Coatings Obtained by Detonation Spraying

Kuchumova, Ivanna D.; Eryomina, M.A.; Lyalina, N. V.; Dudina, Dina V.; Batraev, Igor S.; Ulianitsky, Vladimir Yu.; Штерцер, А. А.; Cherkasova, Nina; Ruktuev, Alexey A.; Ukhina, Arina V.; Borisenko, Tatiana A.; Koga, Guilherme Yuuki; Kiminami, Cláudio S.; Jorge, Alberto Moreira

doi:10.1007/s11665-021-06143-y

Cited by 8 publications

(2 citation statements)

References 29 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Previous studies of corrosion resistance of Fe 66 Cr 10 Nb 5 B 19 detonation coatings with glassy structure showed that the coatings had a high resistance to atmospheric [29] and electrochemical corrosion [30]. Developed coatings can be recommended as protective coatings in aggressive environments.…”

Section: Methodsmentioning

confidence: 99%

Wear resistance of Fe 66 Cr 10 Nb 5 B 19 detonation coatings under dry linearly reciprocating conditions and nanoscratch test

Kuchumova

Shikalov

Batraev

et al. 2022

Preprint

Self Cite

View full text Add to dashboard Cite

The Fe66Cr10Nb5B19 alloy coatings with high hardness (~ 850 HV300), low porosity (less 3%), low content of crystalline phase (less 2.5 wt.%), elevated nanohardness (average value 13.7 GPa), and high wear resistance were obtained in a wide range of detonation spraying modes. The results under dry linearly reciprocating sliding wear tests of coatings and stainless steel carried out according to ASTM G 133-05 are presented. The volume loss of detonation coatings obtained at an explosive charge of 50–70%, measured on an optical profilometer, is significantly lower than that of stainless steel. The similar values of volume scratches of Fe66Cr10Nb5B19 coatings obtained at an explosive charge of 40–70% can be attributed to similar values of porosity and content of crystalline phase. The scratch and spalling mechanisms are the main mechanisms of material removal from the coatings.

show abstract

Section: Methodsmentioning

confidence: 99%

Wear resistance of Fe 66 Cr 10 Nb 5 B 19 detonation coatings under dry linearly reciprocating conditions and nanoscratch test

Kuchumova

Shikalov

Batraev

et al. 2022

Preprint

Self Cite

View full text Add to dashboard Cite

show abstract

“…Te choice of materials and application techniques played a crucial role in determining the level of protection against corrosion. Chromium 20 nickel [7,8], FeCoCrAlNiTix (x: molar ratio, x 1/4 0.5, 1.0, 1.5, and 2.0) [9], tungsten carbide and chromium carbide [10], TiNbMoMnFe high entropy alloy coating [11], sample 316L austenitic stainless steel [12], nanomodifed silicon-based composite coating [13], tube-ftting nuts made of AISI [14], Mg-X alloys (X = Mn, Sn, Ca, Zn, Al, Zr, Si, Sr) [15], titanium nitride [16], arc sprayed aluminum coating [17], Fe 66 Cr 10 Nb 5 B 19 metallic glass coating [18], and titania coated α-Al 2 O 3 platelets [19] are some of the examples. Based on the discussion, it is found that ceramic composite coatings are good for use against corrosion.…”

Section: Introductionmentioning

confidence: 99%

Development of Alumina-Titania Composite Layers on Stainless Steel through the Detonation Spray Method and Investigation of Salt Spray Corrosion Behavior along with Surface Examination

Surya¹,

Prakash²,

Kumar³

et al. 2023

International Journal of Chemical Engineering

View full text Add to dashboard Cite

Almost every metal and alloy corrodes when used in high-temperature applications. To combat this problem, ceramic coatings on the metals can be deposited for better thermal and corrosion behavior. The present study applies an alumina-titania (Al2O3-TiO2) ceramic coating to the stainless steel (SS) surface using a detonation spray process. The surface of the coated SS is probed by optical microscopy (OM), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The clear differences between coated and uncoated SS have been observed based on the SEM images. The XRD pattern indicates that the Al2O3-TiO2 coating on SS has been successfully deposited. The hardness of coated and uncoated SS surfaces is determined by using the Micro Vickers hardness tester, which claims that the hardness of the SS surface has decreased after coating. Salt spray tests were used to examine the corrosion behavior of coated and uncoated SS after 12 and 24 hours. After 12 hours, no corrosion was observed on the SS. After 24 hours, however, significant corrosion of uncoated SS is observed, and the coated SS shows negligible corrosion. Based on the study, it is claimed that an Al2O3-TiO2 coating on SS has improved its corrosion behavior significantly.

show abstract

Effect of Isothermal Annealing on the Corrosion Resistance of Detonation Sprayed Fe-Based Amorphous Coatings

Li,

Xu,

et al. 2024

J. of Materi Eng and Perform

View full text Add to dashboard Cite

Structural Features and Corrosion Resistance of Fe66Cr10Nb5B19 Metallic Glass Coatings Obtained by Detonation Spraying

Cited by 8 publications

References 29 publications

Wear resistance of Fe 66 Cr 10 Nb 5 B 19 detonation coatings under dry linearly reciprocating conditions and nanoscratch test

Wear resistance of Fe 66 Cr 10 Nb 5 B 19 detonation coatings under dry linearly reciprocating conditions and nanoscratch test

Development of Alumina-Titania Composite Layers on Stainless Steel through the Detonation Spray Method and Investigation of Salt Spray Corrosion Behavior along with Surface Examination

Effect of Isothermal Annealing on the Corrosion Resistance of Detonation Sprayed Fe-Based Amorphous Coatings

Contact Info

Product

Resources

About