Surface Wettability Analysis of Nichrome Alloy Based on the Measurements of Sessile Droplet Contact Angles

Kumarasiri, A.; Amarasinghe, D.A.S.; Attygalle, Dinesh

doi:10.1109/mercon50084.2020.9185360

Cited by 8 publications

(1 citation statement)

References 28 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Figure 2 shows that when the energy of the interface in the liquid and gas is in contact with the solid surface, it will produce three interface forces on the solid-liquid, gas-liquid and solid-gas substance. The presence of this force will cause an equilibrium generated by the contact angle through Young's equation [16]:…”

Section: Characterizationmentioning

confidence: 99%

Fabrication and Characterization of Polysulfone Membrane Based On GO-SiO₂ Composite using Phase Inversion Method

Angesti

Munasir

2021

E3S Web Conf.

View full text Add to dashboard Cite

This research purpose to determine the material composition in the manufacture of polysulfone membranes by producing the best performance in the filtration application process. Polysulfone has good thermal and chemical stability properties that make it a candidate material in membrane manufacturing, but the hydrophobicity properties of polysulfone result in less than optimal membrane performance, so a blending process is needed to reduce hydrophobicity by maintaining the advantages of the membrane. The membrane was prepared using phase inversion with composite doping through the TEOS in situ hydrolysis method. The results of XRD identification showed that the diffraction pattern was successfully coated with silica with the amorphous phase, while the FTIR contained Si-O-Si bonds with a wave number of 1054 cm-1. The SEM surface morphology showed that the presence of silica and GO made the pore size larger with the pore size on the membrane 1,92 μm. The results of the contact angle test on the GO-SiO2/PSF variation of 0,8 obtained the lowest hydrophobicity value of 70,17°. The addition of composites will result in a larger pore size supported by the value of the contact angle, proving that the combination of the composite in polysulfone can increase the hydrophilicity of the membrane.

show abstract

Section: Characterizationmentioning

confidence: 99%

Fabrication and Characterization of Polysulfone Membrane Based On GO-SiO₂ Composite using Phase Inversion Method

Angesti

Munasir

2021

E3S Web Conf.

View full text Add to dashboard Cite

show abstract

Microplastics in facial cleanser: extraction, identification, potential toxicity, and continuous-flow removal using agricultural waste–based biochar

Hanif

Ibrahim

Dahalan

et al. 2023

Environ Sci Pollut Res

View full text Add to dashboard Cite

The effect of atmospheric pressure plasma treatment on wetting and absorbance properties of cotton fabric

Sandanuwan

Hendeniya

Amarasinghe

et al. 2021

Materials Today: Proceedings

View full text Add to dashboard Cite

Surface Wettability Analysis of Nichrome Alloy Based on the Measurements of Sessile Droplet Contact Angles

Cited by 8 publications

References 28 publications

Fabrication and Characterization of Polysulfone Membrane Based On GO-SiO₂ Composite using Phase Inversion Method

Fabrication and Characterization of Polysulfone Membrane Based On GO-SiO₂ Composite using Phase Inversion Method

Microplastics in facial cleanser: extraction, identification, potential toxicity, and continuous-flow removal using agricultural waste–based biochar

The effect of atmospheric pressure plasma treatment on wetting and absorbance properties of cotton fabric

Contact Info

Product

Resources

About

Surface Wettability Analysis of Nichrome Alloy Based on the Measurements of Sessile Droplet Contact Angles

Cited by 8 publications

References 28 publications

Fabrication and Characterization of Polysulfone Membrane Based On GO-SiO2 Composite using Phase Inversion Method

Fabrication and Characterization of Polysulfone Membrane Based On GO-SiO2 Composite using Phase Inversion Method

Microplastics in facial cleanser: extraction, identification, potential toxicity, and continuous-flow removal using agricultural waste–based biochar

The effect of atmospheric pressure plasma treatment on wetting and absorbance properties of cotton fabric

Contact Info

Product

Resources

About

Fabrication and Characterization of Polysulfone Membrane Based On GO-SiO₂ Composite using Phase Inversion Method

Fabrication and Characterization of Polysulfone Membrane Based On GO-SiO₂ Composite using Phase Inversion Method