Synergism between mechanical wear and corrosion on tribocorrosion of a titanium alloy in a Ringer solution

Ferreira, Danilo Fontes; Almeida, Susana; Soares, Renata Braga; Juliani, Luciano; Bracarense, Alexandre Queiróz; Lins, Vanessa de Freitas Cunha; Junqueira, Rosa Maria Rabelo

doi:10.1016/j.jmrt.2018.11.004

Cited by 42 publications

(13 citation statements)

References 35 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…After the tribocorrosion ceases, the passivation film again forms on the sample surface and the current returns to its initial state. These observations are consistent with the findings in the existing literature [37]. In addition, the current observed in the raw and nitrided samples can increase as the load increases during sliding.…”

Section: Current Evolution During Slidingsupporting

confidence: 93%

Tribocorrosion Behaviour of a Ti–25Nb–3Zr–2Sn–3Mo Alloys Induction Nitride Layer in a Simulated Body Fluid Solution

Dai

Jiang²,

Ou³

et al. 2023

Coatings

View full text Add to dashboard Cite

Ti–25Nb–3Zr–2Sn–3Mo (TLM) alloys have been used in orthopaedics due to their excellent biocompatibility. However, the poor tribological performance caused by the low shear strength limits the applicability of TLM alloy. Herein, the surface of the TLM alloy was strengthened by induction nitriding technology, and the microstructure of the formed nitride layer as well as its corrosion property were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical workstation. The results showed that a gradient nitride layer with a thickness of ~30 μm was obtained on the surface of the TLM alloy after induction nitriding and the surface microhardness of the TLM alloy also increased from approximately 230 HV to 1253 HV. Meanwhile, the corrosion resistance of the TLM alloy in simulated body fluids (SBFs), was significantly improved by the nitride layer, which was supported by the corrosion potential value increasing from −665.77 (the raw sample) to −241.00 mV (the nitrided sample). Triborrosion behaviour is also characterized by a reciprocating sliding wear tester connected to an electrochemical workstation with different electrochemical conditions. The results evidenced that the TLM alloy has excellent tribocorrosion resistance after induction nitriding, who’s the mechanical material loss (WA) was only 0.23% of that of the raw sample under a 10 N load, and the total material loss (WT) was 15% of that of the raw sample.

show abstract

Section: Current Evolution During Slidingsupporting

confidence: 93%

Tribocorrosion Behaviour of a Ti–25Nb–3Zr–2Sn–3Mo Alloys Induction Nitride Layer in a Simulated Body Fluid Solution

Dai

Jiang²,

Ou³

et al. 2023

Coatings

View full text Add to dashboard Cite

show abstract

“…Meanwhile, the volume loss is also strongly influenced by the electrochemical potentials. Because more strain is accumulated below the surface at passivly applied potentials [28], the volume loss is higher at an anodic potential than in a cathodic potential, especially for the condition of high applied load and speed [29]. Similar observations have been made by other investigators.…”

Section: Effect Of Electrochemical Potentialsupporting

confidence: 85%

“…Thus, if the pure mechanical wear (W wear ) in the solution could be measured, then ∆W would be determined by the difference between W total and W wear . A technique has been suggested and used by several investigators [29,34,35] to evaluate the pure mechanical wear in the test solution, which involved wear testing at a cathodic potential. Since corrosion is limited by cathodic protection (although it does not mean there is absolutely no corrosion), the material loss measured under cathodic potentials in the same media was generally adopted as pure mechanical wear loss W wear .…”

Section: Mechanical Wear and Chemical Wearmentioning

confidence: 99%

Corrosive wear of multi-layer Fe-based coatings laser cladded from amorphous powders

Luo

Sun

et al. 2019

Wear

View full text Add to dashboard Cite

This is a PDF file of an article that has undergone enhancements after acceptance, such as the addition of a cover page and metadata, and formatting for readability, but it is not yet the definitive version of record. This version will undergo additional copyediting, typesetting and review before it is published in its final form, but we are providing this version to give early visibility of the article. Please note that, during the production process, errors may be discovered which could affect the content, and all legal disclaimers that apply to the journal pertain.

show abstract

“…One of the best-known simulated environments used for reactivity and corrosion investigations of biomaterials is the Hanks’ solution [ 17 , 18 , 19 ]. Other solutions include Hanks’ with and without hydrogen peroxide (H 2 O 2 ) [ 17 ]; Hanks’ solution with and without albumin [ 20 ]; Ringer’s solution [ 21 ]; Fusayama Meyer [ 22 , 23 ]; Fusayama Meyer with addition of albumin and hydrogen peroxide [ 24 ]; Fusayama Meyer with addition of fluoride ions, hydrogen peroxide, and lactic acid [ 25 ]; artificial saliva [ 26 ]; artificial saliva with lactic acid [ 27 ]; saline solution 0.9% NaCl [ 28 ]; 0.1 M NaCl with 0.1 M lactic acid [ 29 ]; and phosphate buffered saline solution [ 30 ].…”

Section: Introductionmentioning

confidence: 99%

Reactivity and Corrosion Behaviors of Ti6Al4V Alloy Implant Biomaterial under Metabolic Perturbation Conditions in Physiological Solutions

Benea

Simionescu-Bogatu

2021

Materials

View full text Add to dashboard Cite

The corrosion of implant biomaterials is a well-known critical issue when they are in contact with biological fluids. Therefore, the reactivity of Ti6Al4V implant biomaterials is monitored during immersion in a Hanks’ physiological solution without and with added metabolic compounds, such as lactic acid, hydrogen peroxide, and a mixture of the two. Electrochemical characterization is done by measuring the open circuit potential and electrochemical impedance spectroscopy performed at different intervals of time. Electrochemical results were completed by morphological and compositional analyses as well as X-ray diffraction before and after immersion in these solutions. The results indicate a strong effect from the inflammatory product and the synergistic effect of the metabolic lactic acid and hydrogen peroxide inflammatory compound on the reactivity and corrosion resistance of an implant titanium alloy.

show abstract

Synergism between mechanical wear and corrosion on tribocorrosion of a titanium alloy in a Ringer solution

Cited by 42 publications

References 35 publications

Tribocorrosion Behaviour of a Ti–25Nb–3Zr–2Sn–3Mo Alloys Induction Nitride Layer in a Simulated Body Fluid Solution

Tribocorrosion Behaviour of a Ti–25Nb–3Zr–2Sn–3Mo Alloys Induction Nitride Layer in a Simulated Body Fluid Solution

Corrosive wear of multi-layer Fe-based coatings laser cladded from amorphous powders

Reactivity and Corrosion Behaviors of Ti6Al4V Alloy Implant Biomaterial under Metabolic Perturbation Conditions in Physiological Solutions

Contact Info

Product

Resources

About