Taguchi Yöntemi̇ İle Poli̇mer Hammadde Karişim Opti̇mi̇zasyonu

Ceylan, Yasemin Gündoğdu; Gündüz, Tülin; Ulusu, Hilal Atici

doi:10.46465/endustrimuhendisligi.762648

Cited by 4 publications

(1 citation statement)

References 6 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…It allows the experimental study to be carried out without the consumption of excessive resources (time, material, personnel, equipment, etc.) and the results to be interpreted and all factor effects to be seen [14].…”

Section: Experimental Design Methodsmentioning

confidence: 99%

Optimization of the Cutting Parameters Affecting the Turning of AISI 52100 Bearing Steel Using the Box-Behnken Experimental Design Method

Yıldız

Parlak

2022

Applied Sciences

View full text Add to dashboard Cite

In this study, we aimed to optimize the cutting parameters that affect the minimum temperature and power consumption in the turning of AISI 52100 bearing steel. For this, the Box-Behnken experimental design method, which was used for the lowest number of experiments in the experimental systems created using the response surface method (RSM), was used. The cutting parameters affecting the turning of the AISI 52100 bearing steel were determined as the cutting speed, depth of cut, and feed rate based on a literature research. The temperature and power consumption values were obtained via analyses according to the experimental design method determined by the finite element analysis (FEM) method. The results obtained were analyzed in Design Expert 13 software. According to the analysis results, the parameter values were determined for the minimum temperature and power consumption. The temperature and power consumption variables were affected by all three parameters, namely the cutting speed, depth of cut, and feed rate. For the minimum temperature and power consumption, a cutting speed of 162.427 m/min, depth of cut of 1.395 mm, and feed rate of 0.247 mm/rev, as well as the feed rate parameters, affected both the temperature and power consumption the most. In addition, it was determined that the cutting speed parameter had the least effect on both the temperature and power consumption variables. In addition, validation experiments were carried out in a real experimental environment with optimum values for the cutting parameters. The results showed that the output values obtained within the limits of the study with the obtained equation were quite close (3.3% error for temperature, 6.6% error for power consumption) to the real experimental outputs.

show abstract

Section: Experimental Design Methodsmentioning

confidence: 99%

Optimization of the Cutting Parameters Affecting the Turning of AISI 52100 Bearing Steel Using the Box-Behnken Experimental Design Method

Yıldız

Parlak

2022

Applied Sciences

View full text Add to dashboard Cite

show abstract

Soğuk Haddelenmiş Strenx 700 CR Çeliğinin Nd:YAG Lazer Kaynak Faktörlerinin Taguchi Yöntemi ile Optimizasyonu

Tunçel

Aydın

2023

Çukurova Üniversitesi Mühendislik Fakültesi Dergisi

View full text Add to dashboard Cite

In this study, cold rolled Strenx 700 CR steel with a minimum yield strength of 700 MPa, which is typically used in load bearing structures to produce stronger and lighter structures, is butt welded with Nd:YAG laser welding. The effect of welding factors on tensile strength is investigated by using laser power rate (20%, 40% and 60%), pulse duration (2, 4 and 6 ms) and pulse frequency (3, 5 and 7 hz). By using Taguchi L9 orthogonal experimental design, the number of experiments, which should be 27 when full factorial, is reduced to 9 experiments. The tensile strength test results are optimized by the Taguchi method's larger is better control characteristic. The optimum test combination for maximum tensile strength is determined as A3B2C2 (60%-4 ms-5 hz). The effect of the welding factors on the tensile strength results is analyzed using the analysis of variance (ANOVA) method and it is found that the most effective factor is the laser power rate with 84.26%.

show abstract

Anod Çamurundaki Altının Sulu Ortamda Klorinasyonu Esnasında Çinko Liçinginin Optimizasyonu

Dönmez¹,

Çelik²

2022

European Journal of Science and Technology

View full text Add to dashboard Cite

ÖzBakırı giderilmiş anod çamurundaki altının sulu ortamda klorinasyonuna ait optimizasyonu esnasında çinkonun liçing davranışı incelenmiştir. Çalışmada, Taguchi deneysel tasarımı kullanılmış olup deney planı olarak L 9 (3 4 ) ortogonal dizisi belirlenmiştir. Ön denemeler ışığı altında parametre olarak; reaksiyon sıcaklığı, karıştırma hızı, asit konsantrasyonu ve katı-sıvı oranı seçilmiştir. Çinkonun çözündürülmesine ait optimum şartlar şöyle tespit edilmiştir: reaksiyon sıcaklığı 40 °C, reaksiyon süresi 2700 s, karıştırma hızı 420 dak -1 ve katı-sıvı oranı 0.1 g.mL -1 . Deneysel sonuçlara göre, optimum liç koşulları altında çinko ekstraksiyonunun % 71,8 olduğu gözlenmiştir.

show abstract

Taguchi Yöntemi̇ İle Poli̇mer Hammadde Karişim Opti̇mi̇zasyonu

Cited by 4 publications

References 6 publications

Optimization of the Cutting Parameters Affecting the Turning of AISI 52100 Bearing Steel Using the Box-Behnken Experimental Design Method

Optimization of the Cutting Parameters Affecting the Turning of AISI 52100 Bearing Steel Using the Box-Behnken Experimental Design Method

Soğuk Haddelenmiş Strenx 700 CR Çeliğinin Nd:YAG Lazer Kaynak Faktörlerinin Taguchi Yöntemi ile Optimizasyonu

Anod Çamurundaki Altının Sulu Ortamda Klorinasyonu Esnasında Çinko Liçinginin Optimizasyonu

Contact Info

Product

Resources

About