Technical Note: Homogeneity of Gafchromic ® EBT2 film

Radiochromic films are important tools for assessing complex dose distributions. Gafchromic EBT‐XD films have been designed for optimal performance in the 40–4,000 cGy dose range. We investigated the dosimetric characteristics of these films, including their dose‐response, postexposure density growth, and dependence on scanner orientation, beam energy, and dose rate with applications to high‐dose volumetric‐modulated arc therapy (VMAT) verification. A 10 MV beam from a TrueBeam STx linear accelerator was used to irradiate the films with doses in the 0–4,000 cGy range. Postexposure coloration was analyzed at postirradiation times ranging from several minutes to 48 h. The films were also irradiated with 6 MV (dose rate (DR): 600 MU/min), 6 MV flattening filter‐free (FFF) (DR: 1,400 MU/ min), and 10 MV FFF (DR: 2,400 MU/min) beams to determine the energy and dose‐rate dependence. For clinical examinations, we compared the dose distribution measured with EBT‐XD films and calculated by the planning system for four VMAT cases. The red channel of the EBT‐XD film exhibited a wider dynamic range than the green and blue channels. Scanner orientation yielded a variation of ∼3% in the net optical density (OD). The difference between the film front and back scan orientations was negligible, with variation of ∼1.3% in the net OD. The net OD increased sharply within the first 6 hrs after irradiation and gradually afterwards. No significant difference was observed for the beam energy and dose rate, with a variation of ∼1.5% in the net OD. The gamma passing rates (at 3%, 3 mm) between the film‐ measured and treatment planning system (TPS)‐calculated dose distributions under a high dose VMAT plan in the absolute dose mode were more than 98.9%.PACS number(s): 87.56 Fc

Section: Discussionmentioning

confidence: 68%

Section: Introductionmentioning

confidence: 99%

Gafchromic EBT‐XD film: Dosimetry characterization in high‐dose, volumetric‐modulated arc therapy

Miura¹,

Ozawa

Hosono³

et al. 2016

“…The red and green channels had an

{normalR}^{2}

value of 0.9999 in 0–10 Gy range. The pixel data of red channel was used for further analyses of measurement films, as the correlation curve of the red channel showed highest response gradient in comparison with other channels (48) . Comparison of film measured and LGP calculated dose distribution were done in the axial plane at

Z = 101 mm

, represented in (Fig.…”

Section: Resultsmentioning

confidence: 99%

MAGAT gel and EBT2 film‐based dosimetry for evaluating source plugging‐based treatment plan in Gamma Knife stereotactic radiosurgery

Natanasabapathi

Subbiah

Kale

et al. 2012

This work illustrates a procedure to assess the overall accuracy associated with Gamma Knife treatment planning using plugging. The main role of source plugging or blocking is to create dose falloff in the junction between a target and a critical structure. We report the use of MAGAT gel dosimeter for verification of an experimental treatment plan based on plugging. The polymer gel contained in a head‐sized glass container simulated all major aspects of the treatment process of Gamma Knife radiosurgery. The 3D dose distribution recorded in the gel dosimeter was read using a 1.5T MRI scanner. Scanning protocol was: CPMG pulse sequence with 8 equidistant echoes, TR=7 s, echo step=14 ms, pixel size=0.5 mm x 0.5 mm, and slice thickness of 2 mm. Using a calibration relationship between absorbed dose and spin‐spin relaxation rate (R2), we converted R2 images to dose images. Volumetric dose comparison between treatment planning system (TPS) and gel measurement was accomplished using an in‐house MATLAB‐based program. The isodose overlay of the measured and computed dose distribution on axial planes was in close agreement. Gamma index analysis of 3D data showed more than 94% voxel pass rate for different tolerance criteria of 3%/2 mm, 3%/1 mm and 2%/2 mm. Film dosimetry with GAFCHROMIC EBT 2 film was also performed to compare the results with the calculated TPS dose. Gamma index analysis of film measurement for the same tolerance criteria used for gel measurement evaluation showed more than 95% voxel pass rate. Verification of gamma plan calculated dose on account of shield is not part of acceptance testing of Leksell Gamma Knife (LGK). Through this study we accomplished a volumetric comparison of dose distributions measured with a polymer gel dosimeter and Leksell GammaPlan (LGP) calculations for plans using plugging. We propose gel dosimeter as a quality assurance (QA) tool for verification of plug‐based planning.PACS number: 87.53.Ly, 87.55.‐x, 87.56.N‐

“…Detailed film dosimetry procedure is described in Devic et al and others. ( 22 , 23 , 24 , 25 ) We applied similar procedures for our study. The obtained dose map was compared with TPS‐calculated dose grid using in‐house developed MATLAB codes.…”

Section: Methodsmentioning

confidence: 99%

Indigenously developed multipurpose acrylic head phantom for verification of IMRT using film and gel dosimetry

Natanasabapathi¹,

Subbiah²,

Rath

et al. 2013

The purpose of this study was to validate the newly designed acrylic phantom for routine dosimetric purpose in radiotherapy. The phantom can be used to evaluate and compare the calculated dose and measured dose using film and gel dosimetric methods. In this study, a doughnut‐shaped planning target volume (8.54 cm3) and inner organ at risk (0.353 cm3) were delineated for an IMRT test plan using the X‐ray CT image of the phantom. The phantom consists of acrylic slabs which are integrated to form a human head with a hole in the middle where several dosimetric inserts can be positioned for measurement. An inverse planning with nine coplanar intensity‐modulated fields was created using Pinnacle TPS. For the film analysis, EBT2 film, flatbed scanner, in‐house developed MATLAB codes and ImageJ software were used. The 3D dose distribution recorded in the MAGAT gel dosimeter was read using a 1.5 T MRI scanner. Scanning parameters were CPMG pulse sequence with 8 equidistant echoes, TR=5600, echo step=22 ms, pixel size=0.5 times 0.5, slice thickness=2 mm. Using a calibration relationship between absorbed dose and spin‐spin relaxation rate (R2), R2 images were converted to dose images. The dose comparison was accomplished using in‐house MATLAB‐based graphical user interface named “IMRT3DCMP”. For gel measurement dose grid from the TPS was extracted and compared with the measured dose grid of the gel. Gamma index analysis of film measurement for the tolerance criteria of 2%/2 mm, 1%/1 mm showed more than 90% voxels pass rate. Gamma index analysis of 3D gel measurement data showed more than 90% voxels pass rate for different tolerance criteria of 2%/2 mm and 1%/1 mm. Overall both 2D and 3D measurement were in close agreement with the Pinnacle TPS calculated dose. The phantom designed is cost‐effective and the results are promising, but further investigation is required to validate the phantom with other 3D conformal techniques for dosimetric purpose.PACS numbers: 87.53.Kn, 87.55.km, 87.56.N‐