The Analysis of Methodology of the Assessment and Expected Indicators of Ecological Safety of Atmospheric air in the Russian Federation for 2010-2020 Years

Telichenko, Valeriy; Слесарев, Михаил; Kuzovkina, Tatiana

doi:10.1016/j.proeng.2016.08.235

Cited by 8 publications

(3 citation statements)

References 0 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Balance plans according to the types of potentials and/or resources, you can check simulation modeling, and the response is not received at the end of the plan period, when nothing can be changed [4][5][6], and immediately at the moment of decision on the project, the modeling and analysis of prevailing ecological situation [5][6][7][8][9][10][11][12]. Here especially important is the creation of an environmental monitoring system that fills the reliable information your information base displaying all the processes in the environment [6][7][8][9][10][11][12][13][14][15][16][17][18].…”

Section: Methods Of Formation Of Steady Control Systems Of Ecological mentioning

confidence: 99%

“…Here especially important is the creation of an environmental monitoring system that fills the reliable information your information base displaying all the processes in the environment [6][7][8][9][10][11][12][13][14][15][16][17][18]. These simulation mathematical models allow to identify the imbalance of plans and forecasts to actualize the objectives of the environmental activities, to justify their actual and potential natural production and technological capabilities [7][8][9][10][11][12][13][14][15][16][17][18][19][20][21].…”

Section: Methods Of Formation Of Steady Control Systems Of Ecological mentioning

confidence: 99%

See 1 more Smart Citation

Environmental graphic method for creating area of permissible impact

Слесарев

2018

IOP Conf. Ser.: Mater. Sci. Eng.

View full text Add to dashboard Cite

Abstract. The methods of ecological optimization of influences developed by the author are presented, including: -graphic method of creation of area of admissible influences by the solution of problems of linear programming; -model of identification of dangerous influences simplex method; -method of formation of steady control systems of ecological safety of construction. On simple numerical examples possibilities of mathematical modeling of environmental pressures at stages of life cycle of construction objects are illustrated. In the paper, linear equations of action with constraints and with two variable factors of influence were considered. If we go over to linear relationships with three variable factors of influence, then they will describe the plane in the three-dimensional impact space; the system of linear constraints is a polyhedron, as the domain of permissible impacts in the three-dimensional impact space. Studies carried out by the graphical method of constructing the region of permissible impacts in solving ecological problems of linear programming have shown its effectiveness and visibility, in comparison with the results obtained by calculation. The most effective is the development of environmental safety management systems for construction related to sources, definitions and categories of wastes, as well as the composition and treatment of waste streams, in order to promote waste prevention and the establishment and implementation of mechanisms to prevent generation and minimize waste, as well as recovery and recycling systems waste construction industry.

show abstract

Section: Methods Of Formation Of Steady Control Systems Of Ecological mentioning

confidence: 99%

Section: Methods Of Formation Of Steady Control Systems Of Ecological mentioning

confidence: 99%

Environmental graphic method for creating area of permissible impact

Слесарев

2018

IOP Conf. Ser.: Mater. Sci. Eng.

View full text Add to dashboard Cite

show abstract

“…A critical review of scientific and technical literature shows that the disposal of wastes from various industries remains a challenge since their types and volumes are ever increasing [1][2][3][4][5]. This also applies to the disposal of waste from such industries as production of phosphate mineral fertilizers, alcohol and dairy products.…”

Section: Introductionmentioning

confidence: 99%

Production of environmentally friendly aerated concrete with required construction and operational properties

Tkach

Solovyov²,

Tkach

2018

MATEC Web Conf.

View full text Add to dashboard Cite

Abstract. The purpose of these studies is to justify the feasibility of recycling different types of industrial waste instead of conventional expensive raw materials in production of environmentally friendly aerated concrete with required construction and operational properties. The impact of wastes from various industries on the environmental condition of affected areas, as well as the results of their environmental assessment were analyzed to determine whether these wastes could be used in production of high-performance building materials. The assessment of industrial wastes in aerated concrete production suggests that industrial wastes of hazard class IV can be recycled to produce aerated concrete. An environmentally friendly method for large-scale waste recycling, including a two-step environmentally sustainable mechanism, was developed. The basic quality indicators of the modified aerated concrete proved that the environmental safety could be enhanced by strengthening the structure, increasing its uniformity and improving thermal insulation properties. The modified non-autoclaved aerated concrete products with improved physical and operational properties were developed. They have the following properties: density -D700; class of concrete -В3.5; thermal transmittance coefficient -0.143 W/(m°С); frost resistance -F75.

show abstract