“…The open-circuit voltage under these conditions was V oc = 1.228 V, while the maximum generated power reached the value of P max = 20.3 mW. At such a V oc value, the achieved power of the module is relatively low in comparison with other oxide-based TEGs reported in the literature . The main reason is apparently related to the high internal resistance, R int , of the module.…”
Section: Resultsmentioning
confidence: 75%
“…At such a V oc value, the achieved power of the module is relatively low in comparison with other oxide-based TEGs reported in the literature. 46 The main reason is apparently related to the high internal resistance, R int , of the module.…”
This
work seeks possibilities for advancing the thermoelectric
oxide technology by exploring a module design involving materials
produced by laser processing. A tubular thermoelectric generator of
modular construction with functional elements located parallel to
a pipe-shaped heat source was designed and manufactured. The p- and
n-type counterparts based on Ca3Co4O9 and Ca0.95Pr0.05MnO3 were grown
by the laser floating zone (LFZ) technique, ensuring highly dense
microstructures and giving the unique possibility for fast and crucible-free
processing of the legs with desirable geometry. The detailed structural
and microstructural characterization indicated that the LFZ processing
should be accompanied with an additional thermal annealing step to
equilibrate the phase composition. Although the measured electrical
performance was found close to or slightly higher compared to that
of similar materials produced by other routes, it was still notably
suppressed by the remaining phase impurities affecting the module’s
output. The maximum observed power output of the module containing
12 Ca3Co4O9/Ca0.95Pr0.05MnO3 thermoelectric couples reached up to 20
mW at a temperature gradient of 389 °C and a hot side temperature
of 525 °C. The contribution of
various factors to the overall performance was analyzed. The results
suggest that the power output could be significantly enhanced by decreasing
the contact resistance at the cold side and proper optimization of
the LFZ processing conditions.
“…The open-circuit voltage under these conditions was V oc = 1.228 V, while the maximum generated power reached the value of P max = 20.3 mW. At such a V oc value, the achieved power of the module is relatively low in comparison with other oxide-based TEGs reported in the literature . The main reason is apparently related to the high internal resistance, R int , of the module.…”
Section: Resultsmentioning
confidence: 75%
“…At such a V oc value, the achieved power of the module is relatively low in comparison with other oxide-based TEGs reported in the literature. 46 The main reason is apparently related to the high internal resistance, R int , of the module.…”
This
work seeks possibilities for advancing the thermoelectric
oxide technology by exploring a module design involving materials
produced by laser processing. A tubular thermoelectric generator of
modular construction with functional elements located parallel to
a pipe-shaped heat source was designed and manufactured. The p- and
n-type counterparts based on Ca3Co4O9 and Ca0.95Pr0.05MnO3 were grown
by the laser floating zone (LFZ) technique, ensuring highly dense
microstructures and giving the unique possibility for fast and crucible-free
processing of the legs with desirable geometry. The detailed structural
and microstructural characterization indicated that the LFZ processing
should be accompanied with an additional thermal annealing step to
equilibrate the phase composition. Although the measured electrical
performance was found close to or slightly higher compared to that
of similar materials produced by other routes, it was still notably
suppressed by the remaining phase impurities affecting the module’s
output. The maximum observed power output of the module containing
12 Ca3Co4O9/Ca0.95Pr0.05MnO3 thermoelectric couples reached up to 20
mW at a temperature gradient of 389 °C and a hot side temperature
of 525 °C. The contribution of
various factors to the overall performance was analyzed. The results
suggest that the power output could be significantly enhanced by decreasing
the contact resistance at the cold side and proper optimization of
the LFZ processing conditions.
“…5b). 28 The precise and adaptable technique combining spraycoating and laser structuring is employed to engineer ceramic layers on a versatile substrate, suitable for various applications. A thermoelectric material Ca 3 Co 4 O 9 (10), was employed in the process and affixed onto a exible ceramic substrate.…”
Section: Ceramic Based Thermoelectric Devicesmentioning
confidence: 99%
“…15a). 46 Researchers have conducted investigations into the structural parameters, and electronic band structure, as well as the half-metallic and thermoelectric properties of Sr 2 EuReO 6 compound materials (28). Utilizing density-functional calculations within the framework of the generalized gradient approximation the computational analyses reveal a half-metallic nature in the electronic properties.…”
Section: Metal Composite-based Thermoelectric Devicesmentioning
This review explores the ever-evolving landscape of thermoelectric materials, focusing on the latest trends and innovations in ceramics, thermally conductive gel-like materials, metals, nanoparticles, polymers, and silicon.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.