Transparent Organic Light-Emitting Diodes with Top Electrode Using Ion-Plating Method

Sano, Hironao; Ishida, Ryota; Kura, Tatsuya; Fujita, Sakae; Naka, Shigeki; Okada, Hiroyuki; Takai, Takeshi

doi:10.1587/transele.e98.c.1035

Cited by 3 publications

(1 citation statement)

References 13 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…-High-purity sources can be used. The three most common PVD coating approaches, where (a) shows a vacuum deposition process [158], (b) illustrates a schematic drawing of the ion-plating method [159], and (c) demonstrates the physical sputtering processes [160]. Reproduced with permission from [160].…”

Section: Vacuum Depositionmentioning

confidence: 99%

Solid Particle Erosion Behaviour and Protective Coatings for Gas Turbine Compressor Blades—A Review

et al. 2020

View full text Add to dashboard Cite

Gas turbines (GTEs) are often utilised in harsh environments where the GT components, including compressor vanes and rotor blades, are subject to erosion damage by sand and dust particles. For instance, in a desert environment, the rate of damage made by solid particles erosion (SPE) becomes severe, and therefore results in degradation to the GTE parts, lowering the cycle efficiency, reducing the device lifetime, and increasing the overall cost of the operation. As such, understanding the erosion mechanism caused by solid particles and the effects associated with it is crucial for selecting the appropriate countermeasures and maintaining the system performance. This review paper provides a survey of the available studies on SPE effects on GTEs and surface protective coatings. Firstly, the ductile and brittle SPE mechanism is presented, as well as the ductile-brittle transition region. Then, an in-depth focus on the parameters associated with the SPE, such as particles properties and impingement conditions, is introduced. Furthermore, the existing theoretical models are shown and discussed. Afterwards, erosion resistant coating materials for surface protection and their selection criteria are covered in the review. Finally, the gap in knowledge and future research direction in the field of SPE on GTEs are provided.

show abstract

Section: Vacuum Depositionmentioning

confidence: 99%

Solid Particle Erosion Behaviour and Protective Coatings for Gas Turbine Compressor Blades—A Review

et al. 2020

View full text Add to dashboard Cite

show abstract

Transparent Electrodes for Organic Light‐emitting Diodes

Naka

2018

Transparent Conductive Materials

View full text Add to dashboard Cite

Evaluation of single photon-emission in a small area for organic light-emitting diodes

Azuma,

Okada

2023

Jpn. J. Appl. Phys.

Self Cite

View full text Add to dashboard Cite

Singlel photon-emission in organic light-emitting diodes (OLEDs) has been evaluated. The device structure of ITO/ MoO3 (20 nm)/ α-NPD (50 nm)/ Alq3 (50 nm)/ LiF (1 nm)/ Al (70 nm) was evaporated on an ITO substrate. In addition to the common OLED measurements, photon-counting measurements were carried out, where, the light is extracted through a diameter of 100 μmϕ pinhole, and the voltage was precisely controlled within 5 mV steps using a power supply. By decreasing the voltage below 2.25 V, an average photon counting of “1” was observed at 2.135 V.

show abstract

Transparent Organic Light-Emitting Diodes with Top Electrode Using Ion-Plating Method

Cited by 3 publications

References 13 publications

Solid Particle Erosion Behaviour and Protective Coatings for Gas Turbine Compressor Blades—A Review

Solid Particle Erosion Behaviour and Protective Coatings for Gas Turbine Compressor Blades—A Review

Transparent Electrodes for Organic Light‐emitting Diodes

Evaluation of single photon-emission in a small area for organic light-emitting diodes

Contact Info

Product

Resources

About