Use of Ulva lactuca to identify ammonia toxicity in marine and estuarine sediments

Han²,

et al. 2015

Front. Environ. Sci.

A toxicity identification evaluation (TIE) based on Ulva pertusa spore release was conducted in 3 phases for the identification of the major toxicants in effluent from a wastewater treatment plant (WTP) and the receiving water in an adjacent stream. The toxicity of the final effluent (FE), as compared with raw wastewater, and primary and secondary effluent, showed a greater change over 12-monthly sampling events and appeared to have impacts on the toxicity of the downstream water with a significant correlation (r 2 = 0.89, p < 0.01). In Phase I, toxicity characterization indicated that cations were likely to be the responsible toxicants for the FE. In Phase II, cations such as Cu, Ni, and Zn were found in the FE at higher concentrations than the EC 50 concentrations determined for the standard corresponding metals. When the concentrations of each metal in the FE samples were plotted against the respective toxicity units, only zinc showed a statistically significant correlation with toxicity (r 2 = 0.86, p < 0.01). In Phase III, using spiking and mass balance approaches, it was confirmed that Zn was the major toxicant in the effluent from the WTP. Following a change in the Fenton reagent used, to one with a lower Zn content, the toxicity of the FE greatly decreased in subsequent months. The TIE developed here enabled the toxicity of FEs of the WTP to be tracked and for Zn, originating from a reagent used for Fenton treatment, to be successfully identified as the key toxicant. The TIE method based on U. pertusa demonstrated utility as a low cost and simple tool to identify the risk factors for industrial effluents and provided information on regulatory control and management.

Section: Introductionmentioning

confidence: 99%

Application of the Ulva pertusa bioassay for a toxicity identification evaluation and reduction of effluent from a wastewater treatment plant

Han²,

et al. 2015

Front. Environ. Sci.

Enviro Toxic and Chemistry

Bioavailability assessment of a contaminated field sediment from Patrick Bayou, Texas, USA: Toxicity identification evaluation and equilibrium partitioning

Perron

Burgess

et al. 2009

Self Cite

Contaminated sediments are commonly found in urbanized harbors. At sufficiently high contaminant levels, sediments can cause toxicity to aquatic organisms and impair benthic communities. As a result, remediation is necessary and diagnosing the cause of sediment toxicity becomes imperative. In the present study, six sediments from a highly industrialized area in Patrick Bayou (TX, USA) were subjected to initial toxicity testing with the mysid, Americamysis bahia, and the amphipod, Ampelisca abdita. All sediments were toxic to the amphipods, while sites PB4A, PB6A, and PB9 were the only sites toxic to mysids. Due to its toxicity to both test organisms, site PB6A was chosen for a marine whole sediment phase I toxicity identification evaluation (TIE). Results of the TIE found toxicity to amphipods was primarily due to nonionic organic contaminants (NOCs), rather than cationic metals or ammonia. Causes of mysid toxicity in the TIE were less clear. An assessment of metal bioavailability using equilibrium partitioning (EqP) approaches supported the results of the TIE that cationic metals were not responsible for observed toxicity in PB6A for either organism. Toxic units (TU) calculated on measured concentrations of NOCs in the sediment yielded a total TU of 1.25, indicating these contaminants are contributing to the observed sediment toxicity. Using a combination of these TIE and EqP assessment tools, this investigation was capable of identifying NOCs as the likely class of contaminants causing acute toxicity to amphipods exposed to Patrick Bayou sediment. The cause of mysid toxicity was not definitively determined, but unmeasured NOCs are suspected.

Arch Environ Contam Toxicol

Use of Zeolite for Removing Ammonia and Ammonia-Caused Toxicity in Marine Toxicity Identification Evaluations

Burgess

Perron

Cantwell

et al. 2004

Abstract. Ammonia occurs in marine waters including effluents, receiving waters, and sediment interstitial waters. At sufficiently high concentrations, ammonia can be toxic to aquatic species. Toxicity identification evaluation (TIE) methods provide researchers with tools for identifying aquatic toxicants. For identifying ammonia toxicity, there are several possible methods including pH alteration and volatilization, Ulva lactuca addition, microbial degradation, and zeolite addition. Zeolite addition has been used successfully in freshwater systems to decrease ammonia concentrations and toxicity for several decades. However, zeolite in marine systems has been used less because ions in the seawater interfere with zeolite's ability to adsorb ammonia. The objective of this study was to develop a zeolite method for removing ammonia from marine waters. To accomplish this objective, we performed a series of zeolite slurry and column chromatography studies to determine uptake rate and capacity and to evaluate the effects of salinity and pH on ammonia removal. We also assessed the interaction of zeolite with several toxic metals. Success of the methods was also evaluated by measuring toxicity to two marine species: the mysid Americamysis bahia and the amphipod Ampelisca abdita. Column chromatography proved to be effective at removing a wide range of ammonia concentrations under several experimental conditions. Conversely, the slurry method was inconsistent and variable in its overall performance in removing ammonia and cannot be recommended. The metals copper, lead, and zinc were removed by zeolite in both the slurry and column treatments. The zeolite column was successful in removing ammonia toxicity for both the mysid and the amphipod, whereas the slurry was less effective. This study demonstrated that zeolite column chromatography is a useful tool for conducting marine water TIEs to decrease ammonia concentrations and characterize toxicity.