Winding Design and Fabrication of a Miniature Axial-Flux Motor by Micro-Electroforming

Tsai, Mi-Ching; Hsu, Liang-Yi

doi:10.1109/tmag.2007.896504

Cited by 4 publications

(3 citation statements)

References 10 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The next group consists of three categories. (i) designing and construction of AFIM [6,18,[23][24][25][26][43][44], (ii) use of different materials in motor manufacturing [28][29][30][31][32][33]42] and (iii) studying the effect of different parameters on the motor performance [37][38][39]42]. Finally, almost all the papers have considered solid stator and rotor.…”

Section: Introductionmentioning

confidence: 99%

“…Considering all these features, there are many papers dealing with the analysis and performance prediction [8–23] or design and manufacturing [24–44] of AFIMs. In earlier groups, most of the literature has described quasi‐three‐dimensional (3D) mathematical models or finite‐element analysis (time harmonic or magnetostatic solution).…”

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Investigation of characteristics of a single‐phase axial flux induction motor using three‐dimensional finite element method and d − q model

Nasiri‐Gheidari¹,

Lesani²

2013

IET Electric Power Applications

View full text Add to dashboard Cite

The aim of this study is to find out the performance characteristics of single-phase axial flux induction motors. In this study, three-dimensional time-stepping finite-element method is employed to analyse electromagnetic fields. Both eddy current and saturation effects are considered in the simulation. Since this transient solution is a computationally expensive method, a mathematical model based on d−q-axis theory is presented in this study. Then, the motor's electrical parameters, whose values are requested in the d−q model, are calculated using the analytical method and the DC-charge test of the built motor. The comparison between experimental and simulation results verifies the success of simulation.

show abstract

Section: Introductionmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

Investigation of characteristics of a single‐phase axial flux induction motor using three‐dimensional finite element method and d − q model

Nasiri‐Gheidari¹,

Lesani²

2013

IET Electric Power Applications

View full text Add to dashboard Cite

show abstract

“…Microelectroforming has applied to micronano-metal structure manufacture, and becomes an important technology of nonsilicon-based fabrication [1][2][3][4]. LIGA is a leading technology for producing high aspect ratio metal microcomponents.…”

Section: Introductionmentioning

confidence: 99%

Microstructure and mechanical properties of nanocrystalline nickel prepared by pulse reverse microelectroforming

Shao

Liu

et al. 2012

Journal of Experimental Nanoscience

View full text Add to dashboard Cite

Nanocrystalline nickel was produced by pulse reverse microelectroforming. The pulse microelectroforming was also performed for the comparative purposes. The surface morphology and microstructure of electroformed nickel layers were investigated by scanning electron microscopy and X-ray diffractometry. The microhardness of nickel layers was measured with a Vickers microhardness tester. The friction and wear experiments for nickel layers were performed on a friction and wear tester. The results indicate that the nickel layers prepared by pulse reverse microelectroforming exhibit higher density and their grain sizes in the nanometer range. The nickel layers with fine grains, high microhardness and better wear resistance are obtained at positive current density of 20 A/dm 2 and negative current density of 2 A/dm 2 . The microhardness and wear resistance of nickel layers are improved as the positive and negative current densities are increased.

show abstract

Sustainability Through Leveraging of Extraterrestrial Resources

Ellery

2018

2018 IEEE Conference on Technologies for Sustainability (SusTech)

View full text Add to dashboard Cite

Winding Design and Fabrication of a Miniature Axial-Flux Motor by Micro-Electroforming

Cited by 4 publications

References 10 publications

Investigation of characteristics of a single‐phase axial flux induction motor using three‐dimensional finite element method and d − q model

Investigation of characteristics of a single‐phase axial flux induction motor using three‐dimensional finite element method and d − q model

Microstructure and mechanical properties of nanocrystalline nickel prepared by pulse reverse microelectroforming

Sustainability Through Leveraging of Extraterrestrial Resources

Contact Info

Product

Resources

About