Wireless high-temperature sensing with a chipless tag based on a dielectric resonator antenna

Kubina, Bernd; Schusler, Martin; Mandel, Christian; Mehmood, Arshad; Jakoby, Rolf

doi:10.1109/icsens.2013.6688181

Cited by 54 publications

(24 citation statements)

References 8 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The use of DRA for RFID as well as a sensing device or sensor is quite effective as per the articles referenced. [168][169][170][171][172][173][174][175][176][177] The dedicated applications are further highlighted in Table 5.…”

Section: Rfid/sensormentioning

confidence: 99%

“…The harmonic control technique for the DR in Ku band at 14.25 GHz has been defined by Lucci et al 174 Niroo-Jazi et al 175 have developed an ultra-wide (2 GHz-to-18 GHz) spectrum sensing DRA. Kubina et al 176 have presented a chip-less tag based DRA for the wireless high-temperature sensor (208C-to-3708C) with resonance frequency near 3 GHz with a temperature sensitivity of 307 KHz/8K. Boccard et al 177 have developed a temperature sensor up to 7008C using DRA operating at 2.37 GHz and composed of zirconium tin titanate (Zr 0.8 Sn 0.2 TiO 4 , ZST).…”

Section: Rfid/sensormentioning

confidence: 99%

See 1 more Smart Citation

Dielectric resonator antennas: An application oriented survey

Dash

Khan

Де

2016

Int. J. RF Microw. Comput. Aided Eng.

View full text Add to dashboard Cite

This survey article outlines a comprehensive investigation of research carried out on dielectric resonator antennas (DRAs) in the last three and half decades, in an application‐oriented approach. DRAs have created a remarkable position in antenna engineering for their adept characteristics like high efficiency, low loss, wide bandwidth, compact size, 3‐dimensional modeling flexibility, etc. The use of DRAs for different commercial and defense applications associated with the wireless communication is highlighted in this article. To make a smooth and effective survey article, all the application‐oriented DRAs available in the open literature are classified in five different categories like microwave bands, specific frequency, technology, millimeter‐wave, and miscellaneous types. The ultimate aims of this review article are as follows: (i) highlights the usability of DRAs for different commercial and defense applications, (ii) helpful for the antenna industries/manufacturers to find out the best DRA for any specific application as per their requirement, and (iii) points out research gap in some application domains which will be quite helpful for future antenna researchers. In the authors' opinion, this survey may be helpful to DRA researchers as such a survey process is not available in the open literature.

show abstract

Section: Rfid/sensormentioning

confidence: 99%

Section: Rfid/sensormentioning

confidence: 99%

Dielectric resonator antennas: An application oriented survey

Dash

Khan

Де

2016

Int. J. RF Microw. Comput. Aided Eng.

View full text Add to dashboard Cite

show abstract

“…The second tag is a temperature sensor that has been presented in [16]. The sensor is built from a half-split cylindrical dielectric resonator (DR) placed on a metallic ground plane.…”

Section: Dynamic Interference Suppression For Chipless Wireless Sensorsmentioning

confidence: 99%

Dynamic interference suppression for chipless wireless sensors based on an out-of-band channel estimation method

Kubina

Mandel

Schüßler

et al. 2014

Int. J. Microw. Wireless Technol.

Self Cite

View full text Add to dashboard Cite

A channel estimation method for chipless wireless sensors is presented. The method is developed to suppress interference signals in radio frequency backscatter systems. It uses two adjacent frequency bands to estimate and suppress the disturbing signal of a dynamic interferer. Afterwards a correction of the sensor tag's backscatter signal is achieved. The method has been tested in indoor measurements with a chipless strain sensor and a chipless temperature sensor. A metal block has been deployed as an interferer. In the given scenario, the method has enabled a determination of the sensors' resonance frequencies with relative errors of ,2% in average. A general dependence of the estimation robustness on the peak bandwidth is observed.

show abstract

“…A comparison of recent developments in wireless passive sensors using electromagnetic resonators. [13], [14], [15], [16], [17] and [18] work is a continuation and extension of the research in passive sensors conducted previously at Uni-Freiburg [22], [23], [24].…”

Section: Introductionmentioning

confidence: 96%

A parallel plate dielectric resonator as a wireless passive strain sensor

Aftab

Yousaf

Hoppe

et al. 2015

2015 IEEE Sensors Applications Symposium (SAS)

View full text Add to dashboard Cite

This paper presents a wireless passive strain sensing concept that functions by detuning a dielectric resonator. It is shown how a high Q resonator functions as a wireless passive sensor when correctly matched with an antenna. Finite element and analytical models are compared with experimental data and the sensor cross sensitivity with respect to temperature and humidity are also explored. The sensitivity of the resonance frequency to the strain, temperature and humidity is measured to be 51.6 ppm/µm, 10.09 ppm/K and -0.65 ppm/% respectively.

show abstract

Wireless high-temperature sensing with a chipless tag based on a dielectric resonator antenna

Cited by 54 publications

References 8 publications

Dielectric resonator antennas: An application oriented survey

Dielectric resonator antennas: An application oriented survey

Dynamic interference suppression for chipless wireless sensors based on an out-of-band channel estimation method

A parallel plate dielectric resonator as a wireless passive strain sensor

Contact Info

Product

Resources

About