Untitled

Teowee, G.; McCarthy, K. C.; McCarthy, F. S.; Bukowski, T. J.; Davis, David W.; Uhlmann, D. R.

doi:10.1023/a:1008623323530

Cited by 13 publications

(3 citation statements)

References 4 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Among these methods, chemical solution deposition is one of the more promising techniques, because it provides higher composition control, lower processing temperatures, shorter fabrication time, and relative low cost [41]. It has been reported several chemical solution routes for processing transition metal and rare-earth manganite thin films, i.e., YMnO 3 [22,29,[31][32][33][34][37][38][39][40][41][42][43], GdMnO 3 [13,14,17], BiMnO 3 [5,17], DyMnO 3 [13,17] and LaMnO 3 [44,45]. However, it has been not reported a general chemical solution route for processing rare-earth and transition metal manganite thin films yet.…”

Section: Introductionmentioning

confidence: 99%

Synthesis of orthorhombic rare-earth manganite thin films by a novel chemical solution route

et al. 2011

View full text Add to dashboard Cite

A novel and general chemical solution route for processing high-quality transition metal and rare-earth orthorhombic manganite thin films on Pt(111)/Ti/SiO 2 /Si substrates was reported. The precursor solutions decomposition process of the manganites was studied by TG and DTA techniques, showing the formation of the phase above 650°C in LaMnO 3 and 750°C in both EuMnO 3 and DyMnO 3 thin films. X-ray diffraction and Raman spectroscopic analysis reveal the formation of a pure orthorhombic structure, with a space group Pbnm, in LaMnO 3 , EuMnO 3 and DyMnO 3 thin films annealed at temperatures above the TG phase formation temperature observed. Microstructure and grain morphology of the films were analyzed by SEM and AFM techniques, showing a progressive improvement of the films structures with the increase of the annealing temperature. The temperature dependence of the magnetic response of the LaMnO 3 , EuMnO 3 and DyMnO 3 thin films show typical transition temperatures, compared with those reported for lanthanum, europium and dysprosium manganite single crystals and ceramics.

show abstract

Section: Introductionmentioning

confidence: 99%

Synthesis of orthorhombic rare-earth manganite thin films by a novel chemical solution route

et al. 2011

View full text Add to dashboard Cite

show abstract

“…process from a 0.25 M yttrium manganate solution prepared using yttrium acetate, manganese acetate and methanol [94]. The solution was spin-coated at 2000 rpm for 30 s on platinized silicon wafers and then fired in oxygen at 400 • C between successive coatings.…”

Section: Ymno 3 Teowee Et Al Synthesized Ymno 3 Films Via Sol-gelmentioning

confidence: 99%

Synthesis of multifunctional multiferroic materials from metalorganics

Singh

Yang

Takoudis

2009

Coordination Chemistry Reviews

View full text Add to dashboard Cite

“…However, the sintering of YMO appears to be a time and energy-consuming process. To prevent the formation of impurity phases, like Mn 3 O 4 , YMn 2 O 5 and Y 2 O 3 , sintering process is usually divided into several long high-temperature thermal treatments with intermediate grinding steps [13,15,[23][24][25]. Following this pattern, the sintering process can last for several days.…”

Section: Introductionmentioning

confidence: 99%

Processing and properties of ceramic yttrium manganite sintered by different methods

Počuča-Nešić

Marinkovic-Stanojevic

Radović

et al. 2021

SCI SINTER

View full text Add to dashboard Cite

Intergranular and intragranular cracks that usually form during sintering of yttrium manganite (YMnO3) ceramic samples hinder the densification process of this ceramic and deteriorate its magnetic and ferroelectric properties. To overcome this problem, mechanochemically synthesized YMnO3 powder was sintered using two different processes: Conventional Sintering (CS) and Pulsed Electric Current Sintering (PECS). All samples were characterized by XRD, SEM and FESEM and their magnetic and ferroelectric properties were investigated. Apart from their phase composition, conventionally sintered ceramic samples showed cracks throughout their whole volume, reaching a maximum relative density of 85 %. However, it was found that PECS process could significantly reduce the presence of cracks within samples whose relative density reached 99.8 %.

show abstract

Untitled

Cited by 13 publications

References 4 publications

Synthesis of orthorhombic rare-earth manganite thin films by a novel chemical solution route

Synthesis of orthorhombic rare-earth manganite thin films by a novel chemical solution route

Synthesis of multifunctional multiferroic materials from metalorganics

Processing and properties of ceramic yttrium manganite sintered by different methods

Contact Info

Product

Resources

About