The aim of the research, the results of which are presented in the paper, is to fabricate, by Selective Laser Melting (SLM), a metallic scaffold with Ti6Al4V powder based on a virtual model corresponding to the actual loss of a patient's craniofacial bone. A plaster cast was made for a patient with a palate recess, and the cast was then scanned with a 3D scanner to create a virtual 3D model of a palate recess, according to which a 3D model of a solid implant was created using specialist software. The virtual 3D solid implant model was converted into a 3D porous implant model after designing an individual shape of the unit cell conditioning the size and three-dimensional shape of the scaffold pores by multiplication of unit cells. The data concerning a virtual 3D porous implant model was transferred into a selective laser melting (SLM) device and a metallic scaffold was produced from Ti6Al4V powder with this machine, which was subjected to surface treatment by chemical etching. An object with certain initially adopted assumptions, i.e. shape and geometric dimensions, was finally achieved, which perfectly matches the patient bone recesses. The scaffold created was subjected to micro-and spectroscopic examinations.Keywords: biomimetic materials, CAMD, scaffolds, SLM, Ti6Al4V powders, SEM, EDS Celem badań, których wyniki zaprezentowano w artykule jest wytworzenie, metodą selektywnego topienia laserowego (SLM), scaffoldu metalowego z proszku Ti6Al4V na podstawie wirtualnego modelu odpowiadającego rzeczywistemu ubytkowi kości twarzoczaszki pacjenta. Od pacjenta z ubytkiem podniebienia pobierano wycisk gipsowy, który następnie zeskanowano za pomocą skanera 3D, w celu uzyskania wirtualnego modelu 3D ubytku podniebienia, na podstawie którego z użyciem specjalistycznego oprogramowania utworzono model 3D litego implantu. Po zaprojektowaniu indywidualnego kształtu komórki jednostkowej, determinującej wielkość i trójwymiarowy kształt porów scaffoldu, poprzez multiplikację komórek jednostkowych przekształcono wirtualny model 3D implantu litego w model 3D implantu porowatego. Dane dotyczące wirtualnego modelu 3D implantu porowatego przetransferowano do urządzenia służącego do selektywnego topienia laserowego (SLM) i z użyciem tej maszyny z proszku Ti6Al4V wytworzono metalowy scaffold, który poddano obróbce powierzchniowej poprzez trawienie chemiczne. Finalnie otrzymano obiekt o założonych na wstępie: kształcie i wymiarach geometrycznych, które idealnie odpowiadają ubytkowi kości pacjenta. Wytworzony scaffold poddano badaniom mikroi spektroskopowym.

This paper presents a comparison of the impact of milling technology in the computer numerically controlled (CNC) machining centre and selective laser sintering (SLS) and on the structure and properties of solid Ti6Al4V alloy. It has been shown that even small changes in technological conditions in the SLS manufacturing variant significantly affect changes from two to nearly two and a half times in tensile and bending strengths. Both the tensile and bending strength obtained in the most favourable manufacturing variant by the SLS method is over 25% higher than in the case of cast materials subsequently processed by milling. Plug-and-play SLS conditions provide about 60% of the possibilities. Structural, tribological and electrochemical tests were carried out. In vitro biological tests using osteoblasts confirm the good tendency for the proliferation of live cells on the substrate manufactured under the most favourable SLS conditions. The use of SLS additive technology for the manufacturing of dental implants and abutments made of Ti6Al4V alloy in combination with the digitisation of dental diagnostics and computer-aided design and manufacture of computer-aided design/manufacturing (CAD/CAM) following the idea of Dentistry 4.0 is the best choice of technology for manufacturing of prosthetic and implant devices used in dentistry.

The aim of the investigations described in this article is to present a selective laser sintering and melting technology to fabricate metallic scaffolds made of pristine titanium and titanium Ti6Al4V alloy powders. Titanium scaffolds with different properties and structure were manufactured with this technique using appropriate conditions, notably laser power and laser beam size. The purpose of such elements is to replace the missing pieces of bones, mainly cranial and facial bones in the implantation treatment process. All the samples for the investigations were designed in CAD/CAM (3D MARCARM ENGINEERING AutoFab (Software for Manufacturing Applications) software suitably integrated with an SLS/SLM system. Cube-shaped test samples dimensioned 10×10×10 mm were designed for the investigations using a hexagon-shaped base cell. The so designed 3D models were transferred to the machine software and the actual rapid manufacturing process was commenced. The samples produced according to the laser sintering technology were subjected to chemical processing consisting of etching the scaffolds’ surface in different chemical mediums. Etching was carried out to remove the loosely bound powder from the surface of scaffolds, which might detach from their surface during implantation treatment and travel elsewhere in an organism. The scaffolds created were subjected to micro- and spectroscopic examinations

Purpose: The publication aims to find the relationship between the proliferation of surface layers of living cells and the deposition of thin atomic layers deposition ALD coatings on the pores internal surfaces of porous skeletons of medical and dental implant-scaffolds manufactured with the selective laser deposition SLS additive technology using titanium and Ti6Al4V alloy. Design/methodology/approach: The extensive review of the literature presents the state-of-the-art in the field of regenerative medicine and tissue engineering. General ageing of societies, increasing the incidence of oncological diseases and some transport and sports accidents, and also the spread of tooth decay and tooth cavities in many regions of the world has taken place nowadays. Those reasons involve resection of many tissues and organs and the need to replace cavities, among others bones and teeth through implantation, more and more often hybridized with tissue engineering methods. Findings: The results of investigations of the structure and properties of skeleton microporous materials produced from titanium and Ti6Al4V alloy powders by the method of selective laser sintering have been presented. Particularly valuable are the original and previously unpublished results of structural research using high-resolution transmission electron microscope HRTEM. Particular attention has been paid to the issues of surface engineering, in particular, the application of flat TiO2 and Al2O3 coatings applied inside micropores using the atomic layers deposition ALD method and hydroxyapatite applied the dip-coating sol-gel method, including advanced HRTEM research. The most important part of the work concerns the research of nesting and proliferation of live cells of osteoblasts the hFOB 1.19 (Human ATCC - CRL - 11372) culture line on the surface of micropores with surfaces covered with the mentioned layers. Research limitations/implications: The investigations reported in the paper fully confirmed the idea of the hybrid technology of producing microporous implants and implant-scaffolds to achieve original Authors’ biological-engineering materials. The surface engineering issues, including both flat-layered nonorganic coatings and interactions of those coverings with flat layers of living cells, play a crucial role. Originality/value: Materials commonly used in implantology and the most commonly used materials processing technologies in those applications have been described. Against that background, the original Authors' concept of implant-scaffolds and the application of microporous skeleton materials for this purpose have been presented.

The general goals of advanced digitized production in the Industry 4.0 stage of the industrial revolution were presented along with the extended holistic model of Industry 4.0, introduced by the authors, indicating the importance of material design and the selection of appropriate manufacturing technology. The effect of the global lockdown caused by the SARS-CoV-2 virus transmission pandemic was a drastic decrease in production, resulting in a significant decrease in the gross domestic product GDP in all countries, and gigantic problems in health care, including dentistry. Dentists belong to the highest risk group because the doctor works in the patient’s respiratory tract. This paper presents a breakthrough authors solution, implemented by the active SPEC strategy, and aims to eliminate clinical aerosol at the source by negative pressure aspirating bioaerosol at the patient’s mouth line. The comparative benchmarking analysis and its results show that only the proprietary solution with a set of devices eliminates the threat at the source, while the remaining known methods do not meet the expectations. The details of this solution are described. Photopolymer materials and additive Digital Light Printing (DLP) technology were used.