Micro‐injection moulding is one of the key manufacturing technologies for thermoplastic polymeric materials for the mass production of high value miniaturized components. However, this process is not just a straightforward down scaling of the conventional injection moulding technique. Indeed, during the micro‐injection the polymer melt is forced to flow at high strain rates through very small channels in nonisothermal conditions; this can lead to complex microstructures and to parts with unexpected performances. In this work, the relationships among the processing conditions, the mechanical properties and the microstructural characteristics of polyoxymethylene miniaturized specimens obtained by injection moulding were investigated. The attention was focused on the influence of the process temperatures on the mechanical behavior, examined by uniaxial tensile tests, and on the microstructural characteristics of the specimens, examined by differential scanning calorimetry, wide‐angle X‐ray diffraction, polarized light microscopy, and dynamic‐mechanical thermal analysis. The results highlighted that material ductility in the miniaturized specimens is significantly affected by the mould temperature, because of the sample microstructure. Different degrees of orientation of polymer crystallites and different morphologies of the skin/core transition region were observed in dependence on the process temperatures. POLYM. ENG. SCI., 54:512–521, 2014. © 2013 Society of Plastics Engineers

Many research efforts have gone in the production of carbon nanotubes (CNT) composites for functional and structural applications and many processing methodologies have been experimented. Twin-screw extrusion appears to be the most suitable way from the perspective of production scale up and commercialization of these composites. At the same time, micro-injection molding process is considered as the key manufacturing technology for the mass production of miniaturized components and devices. Despite the massive literature about nanocomposites and microinjection molding process, few articles focus on the interaction between the compounding process and the following micro-injection molding transformation processes. This article aims at analyzing the influence of the screw configuration used in compounding process on the rheological and technological properties of the resulting nanocomposites. Two different combinations of screw elements have been tested to incorporate CNTs in two different resins: LCP (liquid crystal polymer) and POM (polyoxymethylene) typically used in micro-injection molding. The effects of the process set up have been observed studying first the rheology and then the moldability of nano-compounds microinjected ribs with high aspect ratio. The nanofiller dispersion has been evaluated via light and transmission electron microscopy. The results confirm that, the screws show different capacity at promoting the dispersion of the nanofiller, which affects the moldability of micro-injected CNT nanocomposites. The viscosity of the polymer seems a critical factor as well, because it influences first the dispersion of CNT bundle during extrusion and then the injection moldability of the composites in the micro-channels

Micro-injection moulding is one of the key manufacturing technologies for the mass production of high value polymeric miniaturized-components. However, this process is not just a straightforward down scaling of the conventional injection moulding technique. Indeed, during the micro-injection the polymer melt is forced to flow at high strain rates through very small channels in non-isothermal conditions, and this can lead to complex microstructures and to parts with unexpected performances. In this work, the relationships among the processing conditions, the mechanical properties and the microstructural characteristics of miniaturized specimens obtained by injection moulding were investigated. Two model systems were considered with the same filler content of 15% wt. (HDPE-talc and HDPE-glass beads), representative of two different types of micro-composites: containing lamellar and spherical micro-particles, respectively. The attention was focused on the influence of the filler type and the process conditions on the mechanical behaviour, examined by uniaxial tensile tests and dynamic-mechanical analyses, and on the morphological characteristics of the specimens, examined by microscopy analyses. The results highlight that mechanical response of the miniaturized specimens is significantly affected by both the filler and the process conditions that can have an influence on the polymer microstructure. Lamellar composites showed the best performance due to the orientation of the talc particles during the micro-injection process, while, different morphologies of the skin/core transition region in dependence on the process temperatures were observable.

Due to its high efficiency for the large scale production of polymeric parts, micro injection moulding is one of the key technologies of the new millennium. Although a lot of researches have been conducted to identify the most effective processing conditions for micro injection moulding, the comprehension of the influence of all parameters on the quality, the properties and the reliability of the moulded parts is still an issue. In this context, this study aims to evaluate the effects of the micro injection moulding process conditions on the tensile properties of micro parts, investigating the influence of three main process parameters: the injection speed, the mould temperature and the melt temperature. A full factorial plan has been applied to study the contributions of these parameters and a second study has been performed to understand the synergic interaction between the two temperatures on the tensile strength. Due to its high level of potential crystallinity, a typical semi-crystalline thermoplastic resin was used in the experiments. The results of the analysis showed a great influence of the mould temperature (Tmould) on the ultimate tensile strength and of the melt temperature (Tmelt) on the deformation at the point of breaking; whereas the injection speed was significant on the overall mechanical performance. A new studied factor (Tmelt-Tmould) could affect the resulting molecular structure and consequently the mechanical behaviour, but itself is not sufficient to thoroughly explain the observed behaviour. Moreover, the visual inspection of the deformation mechanism at break shows three distinctive trends demonstrating the great variability of the mechanical properties of micro-injected specimens due to process conditions.

No abstract