The ability to design S-shaped ducts with high aerodynamic loading is advantageous from a performance and/or weight saving perspective. However, the radial pressure gradients required to turn the flow produce strong pressure gradients in the axial direction. This promotes the likelihood of flow separation from the inner casing as the loading is increased. The current paper presents a novel approach to accommodating the increased loading by bleeding an amount of air from the critical inner casing. The process through which the air is bled re-energizes the boundary layer sufficiently to enable it to remain attached despite the high duct loading. A bled duct is numerically developed and experimentally evaluated using a fully annular isothermal facility, with representative inlet conditions provided by a single stage axial compressor. The measurements indicate successful operation of this new design concept with a reduction in the overall system length, compared to a conventional design, of approximately 30% and a reduction in loss of approximately 20%. The data also demonstrate, to a limited degree, the ability to control the flow distribution at duct exit ultimately improving flow uniformity. Furthermore, the pressure of the bled flow is higher than at rotor exit where, in current engine architectures, flow is typically removed from the main gas path. In other words current engine bleed locations could be replaced by a bleed flow within the transition duct, and this flow is of sufficient pressure to meet the existing requirements associated with cooling, sealing and/or zone ventilation.

In a multistage intermediate pressure compressor an efficiency benefit may be gained by reducing reaction in the rear stages, and allowing swirl to persist at the exit. This swirl must now be removed within the transition duct that is situated between the intermediate and high pressure compressor spools, in order to present the downstream compressor with suitable inlet conditions. This paper presents the numerical design and experimental validation of an initial concept which uses a lifting strut to remove tangential momentum from the flow within an S-shaped compressor transition duct. The design methodology uses an existing strut profile with the camber line modified to remove a specified amount of the inlet tangential momentum. A linear strut loading was employed in the meridional direction with a nominally constant loading in the radial direction. This approach was applied to an existing aggressive S-duct configuration in which approximately 12.5° of swirl remains at OGV exit. 3D CFD predictions were used for preliminary assessment of duct loading and to determine how much swirl could be removed. Consequently, a fully annular test facility incorporating a 1½ stage axial compressor was used to experimentally evaluate four configurations; an unstrutted duct, a non-lifting strut and lifting struts designed to remove 50% and 75% of the inlet tangential momentum. Despite the expected large increase in loss caused by the introduction of struts there was not a significant additional loss measured with the inclusion of turning. No evidence of flow separation was observed and the data suggested that it may be possible to remove more swirl than was attempted. Although the turning struts did not remove the entire targeted swirl due to viscous deviation the data still confirm the feasibility of using a lifting strut/duct concept which has the potential to off-load the rear stages of the upstream compressor.

No abstract

Within gas turbines the ability to design shorter aggressive S-shaped ducts is advantageous from a performance and weight saving perspective. However, current design philosophies tend to treat the S-shaped duct as an isolated component, neglecting the potential advantages of integrating the design with the upstream or downstream components. In this paper, such a design concept is numerically developed in which the upstream compressor outlet guide vanes are incorporated into the first bend of the S-shaped duct. Positioning the vane row within the first bend imparts a strong radial gradient to the pressure field within the vane passage. Tangential lean and axial sweep are employed such that the vane geometry is modified to exactly match the resulting inclined static pressure field. The integrated design is experimentally assessed and compared to a conventional nonintegrated design on a fully annular low speed test facility incorporating a single stage axial compressor. Several traverse planes are used to gather five-hole probe data which allow the flow structure to be examined through the rotor, outlet guide vane and within the transition ducts. The two designs employ almost identical duct geometry, but integration of the vane row reduces the system length by 21%. Due to successful matching of the static pressure field, the upstream influence of the integrated vane row is minimal and the rotor performance is unchanged. Similarly, the flow development within both S-shaped ducts is similar such that the circumferentially averaged profiles at duct exit are almost identical, and the operation of a downstream component would be unaffected. Overall system loss remains nominally unchanged despite the inclusion of lean and sweep and a reduction in system length. Finally, the numerical design predictions show good agreement with the experimental data thereby successfully validating the design process.

No abstract