International audienceA holistic view of the Bengal–Nicobar Fan system requires sampling the full sedimentary section of the Nicobar Fan, which was achieved for the first time by International Ocean Discovery Program (IODP) Expedition 362 west of North Sumatra. We identified a distinct rise in sediment accumulation rate (SAR) beginning ∼9.5 Ma and reaching 250–350 m/Myr in the 9.5–2 Ma interval, which equal or far exceed rates on the Bengal Fan at similar latitudes. This marked rise in SAR and a constant Himalayan-derived provenance necessitates a major restructuring of sediment routing in the Bengal–Nicobar submarine fan. This coincides with the inversion of the Eastern Himalayan Shillong Plateau and encroachment of the west-propagating Indo–Burmese wedge, which reduced continental accommodation space and increased sediment supply directly to the fan. Our results challenge a commonly held view that changes in sediment flux seen in the Bengal–Nicobar submarine fan were caused by discrete tectonic or climatic events acting on the Himalayan–Tibetan Plateau. Instead, an interplay of tectonic and climatic processes caused the fan system to develop by punctuated changes rather than gradual progradation

International audienceTrying to understand where major earthquakes and tsunamis might occur requires analysis of the sediments pouring into a subduction zone. Thick sediments were expected to limit earthquake and tsunami size in the Sumatran megathrust event in 2004, but the magnitude 9.2 earthquake defied expectations. Hüpers et al. analyzed sediments recovered from the Sumatran megathrust. They found evidence of sediment dehydration, which increased fault strength and allowed for the much larger earthquake to occur. Thus, models of other subduction zones, such as the Gulf of Alaska, may underestimate the maximum earthquake magnitude and tsunami risk

No abstract

Phyllosilicates weaken faults due to the formation of shear fabrics. Although the impacts of clay abundance and fabric on frictional strength, sliding stability, and porosity of faults are well studied, their influence on elastic properties is less known, though they are key factors for fault stiffness. We document the role that fabric and consolidation play in elastic properties and show that smectite content is the most important factor determining whether fabric or porosity controls the elastic response of faults. We conducted a suite of shear experiments on synthetic smectite‐quartz fault gouges (10–100 wt% smectite) and sediment incoming to the Sumatra subduction zone. We monitored Vp, Vs, friction, porosity, shear and bulk moduli. We find that mechanical and elastic properties for gouges with abundant smectite are almost entirely controlled by fabric formation (decreasing mechanical and elastic properties with shear). Though fabrics control the elastic response of smectite‐poor gouges over intermediate shear strains, porosity is the primary control throughout the majority of shearing. Elastic properties vary systematically with smectite content: High smectite gouges have values of Vp ~ 1,300–1,800 m/s, Vs ~ 900–1,100 m/s, K ~ 1–4 GPa, and G ~ 1–2 GPa, and low smectite gouges have values of Vp ~ 2,300–2,500 m/s, Vs ~ 1,200–1,300 m/s, K ~ 5–8 GPa, and G ~ 2.5–3 GPa. We find that, even in smectite‐poor gouges, shear fabric also affects stiffness and elastic moduli, implying that while smectite abundance plays a clear role in controlling gouge properties, other fine‐grained and platy clay minerals may produce similar behavior through their control on the development of fabrics and thin shear surfaces.

The elastic and mechanical properties of fault gouge are key controls on fault zone stiffness, strength, damage, healing, and sliding stability. Clay minerals are prevalent in fault zones and have significant effects on friction, porosity, elastic properties, and shear fabric development. Although clay-rich gouges are well studied, the roles of porosity evolution and fabric formation in modulating elastic and mechanical properties are unclear. We have found that with progressive shear, the role of strain localization and fabric development may compete with densification to control the evolution of friction and elastic moduli. We report on a suite of double-direct shear experiments on synthetic gouge composed of 50% Ca-montmorillonite and 50% granular quartz at a normal stress of 25 MPa. We measure the coefficient of friction, porosity, P and S wave speeds, and bulk and shear moduli, and their evolution with shearing, to shear strains up to~25. We find that the evolution of V p , V s , and elastic moduli are controlled by the interplay of porosity loss, shear fabric development, and particle contact stiffness. In general, V p , V s , and elastic moduli increase with shear strain and are accompanied by gradual densification and porosity loss. However, at intermediate shear strains (~2-8) a decrease in V p , V s , and elastic moduli is superimposed on this overall trend. Based on previous microstructural studies, we hypothesize that fabrics develop parallel to shear direction (perpendicular to wave propagation) over this range of strains, leading to reduced fault stiffness and competing with porosity loss as the dominant control on elastic properties.