A novel sol-gel method is described for the preparation of solid-phase microextraction (SPME) fibers. The protective polyimide coating was removed from a 1-cm end segment of a 200 μm o.d. fused-silica fiber, and the exposed outer surface was coated with a bonded sol-gel layer of poly(dimethylsiloxane) (PDMS). The chemistry behind this coating technique is presented. Efficient SPME-GC analyses of polycyclic aromatic hydrocarbons, alkanes, aniline derivatives, alcohols, and phenolic compounds in dilute aqueous solutions were achieved using sol-gel-coated PDMS fibers. The extracted analytes were transferred to a GC injector using an in-house-designed SPME syringe that also allowed for easy change of SPME fibers. Electron microscopy experiments suggested a porous structure for the sol-gel coating with a thickness of ∼10 μm. The coating porosity provided higher surface area and allowed for the use of thinner coatings (compared with 100-μm-thick coatings for conventional SPME fibers) to achieve acceptable stationary-phase loadings and sample capacities. Enhanced surface area of sol-gel coatings, in turn, provided efficient analyte extraction rates from solution. Experimental results on thermal stability of sol-gel PDMS fibers were compared with those for commercial 100-μm PDMS fibers. Our findings suggest that sol-gel PDMS fibers possess significantly higher thermal stability (>320 °C) than conventionally coated PDMS fibers that often start bleeding at 200 °C. This is due, in part, to the strong chemical bonding between the sol-gel-generated organic-inorganic composite coating and the silica surface. Enhanced thermal stability allowed the use of higher injection port temperatures for efficient desorption of less-volatile analytes and should translate into extended range of analytes that can be handled by SPME-GC techniques. Experimental evidence is provided that supports the operational advantages of sol-gel coatings in SPME-GC analysis.

Sol-gel capillary microextraction (sol-gel CME) is introduced as a viable solventless extraction technique for the preconcentration of trace analytes. To our knowledge, this is the first report on the use of sol-gel-coated capillaries in analytical microextraction. Sol-gel-coated capillaries were employed for the extraction and preconcentration of a wide variety of polar and nonpolar analytes. Two different types of sol-gel coatings were used for extraction: sol-gel poly(dimethylsiloxane) (PDMS) and sol-gel poly(ethylene glycol) (PEG). An in-house-assembled gravity-fed sample dispensing unit was used to perform the extraction. The analysis of the extracted analytes was performed by gas chromatography (GC). The extracted analytes were transferred to the GC column via thermal desorption. For this, the capillary with the extracted analytes was connected to the inlet end of the GC column using a two-way press-fit fused-silica connector housed inside the GC injection port. Desorption of the analytes from the extraction capillary was performed by rapid temperature programming (at 100 degrees C/min) of the GC injection port. The desorbed analytes were transported down the system by the helium flow and further focused at the inlet end of the GC column maintained at 30 degrees C. Sol-gel PDMS capillaries were used for the extraction of nonpolar and moderately polar compounds (polycyclic aromatic hydrocarbons, aldehydes, ketones), while sol-gel PEG capillaries were used for the extraction of polar compounds (alcohols, phenols, amines). The technique is characterized by excellent reproducibility. For both polar and nonpolar analytes, the run-to-run and capillary-to-capillary RSD values for GC peak areas remained under 6% and 4%, respectively. The technique also demonstrated excellent extraction sensitivity. Parts per quadrillion level detection limits were achieved by coupling sol-gel CME with GC-FID. The use of thicker sol-gel coatings and longer capillary segments of larger diameter (or capillaries with sol-gel monolithic beds) should lead to further enhancement of the extraction sensitivity.

Sol-gel chemistry was used to prepare porous monolithic columns for capillary electrochromatography. The developed sol-gel approach proved invaluable and generates monolithic columns in a simple and rapid manner. Practically any desired column length ranging from a few tens of centimeters to a few meters may be readily obtained. The incorporation of the sol-gel precursor, N-octadecyldimethyl[3-(trimethoxysilyl)propyl]ammonium chloride, into the sol solution proved to be critical as this reagent possesses an octadecyl moiety that allows for chromatographic interactions of analytes with the monolithic stationary phase. Additionally, this reagent served to yield a positively charged surface, thereby providing the relatively strong reversed electroosmotic flow (EOF) in capillary electrochromatography. The enhanced permeability of the monolithic capillaries allowed for the use of such columns without the need for modifications to the commercial CE instrument. There was no need to pressurize both capillary ends during operation or to use high pressures for column rinsing. With the developed procedure, no bubble formation was detected during analysis with the monolithic capillaries when using electric field strengths of up to 300 V cm(-1). The EOF in the monolith columns was found to be dependent on the percentage of organic modifier present in the mobile phase. Separation efficiencies of up to 1.75 x 10(5) plates/m (87,300 plates/column) were achieved on a 50 cm x 50 microm i.d. column using polycyclic aromatic hydrocarbons and aromatic aldehydes and ketones as test solutes.

The separation and detection of complexes of aptamers and protein targets by capillary electrophoresis (CE) with laser-induced fluorescence was examined. Aptamer-thrombin and aptamer-immunoglobulin E (IgE) were used as model systems. Phosphate, 3-(N-morpholino)propanesulfonic acid with phosphate, and tris(hydroxyamino)methane-glycine-potassium (TGK) buffer at pH 8.4 were tested as electrophoresis media. Buffer had a large effect with TGK providing the most stable complexes for both protein-aptamer complexes. Conditions that suppressed electroosmotic flow, such as addition of hydroxypropylmethylcellulose to the media or modification of the capillary inner wall with polyacrylamide, were found to prevent detection of complexes. The effect of separation time and electric field were evaluated by monitoring complexes with electric field varied from 150-2850 V/cm and effective column lengths of 3.5 and 7.0 cm. As expected, shorter times on the column greatly increased peak heights for the complexes due to a combination of less dilution by diffusion and less dissociation on the column. High fields were found to have a detrimental effect on detection of complexes. It is concluded that the best conditions for detection of noncovalent complexes involve use of the minimal column length and electric field necessary to achieve separation. The results will be of interest in developing affinity probe CE assays wherein aptamers are used as affinity ligands.

No abstract