A poly(glycerol monomethacrylate) (PGMA) macromolecular chain transfer agent has been utilized to polymerize benzyl methacrylate (BzMA) via reversible addition−fragmentation chain transfer (RAFT)-mediated aqueous emulsion polymerization. This formulation leads to the efficient formation of spherical diblock copolymer nanoparticles at up to 50% solids. The degree of polymerization (DP) of the core-forming PBzMA block has been systematically varied to control the mean particle diameter from 20 to 193 nm. Conversions of more than 99% were achieved for PGMA 51 −PBzMA 250 within 6 h at 70 °C using macro-CTA/initiator molar ratios ranging from 3.0 to 10.0. DMF GPC analyses confirmed that relatively low polydispersities (M w /M n < 1.30) and high blocking efficiencies could be achieved. These spherical nanoparticles are stable to both freeze−thaw cycles and the presence of added salt (up to 0.25 M MgSO 4 ). Three sets of PGMA 51 −PBzMA x spherical nanoparticles have been used to prepare stable Pickering emulsions at various copolymer concentrations in four model oils: sunflower oil, n-dodecane, nhexane, and isopropyl myristate. A reduction in mean droplet diameter was observed via laser diffraction on increasing the nanoparticle concentration. Finally, the cis diol functionality on the PGMA stabilizer chains has been exploited to demonstrate the selective adsorption of PGMA 51 −PBzMA 100 nanoparticles onto a micropatterned phenylboronic acid-functionalized planar surface. Formation of a cyclic boronate ester at pH 10 causes strong selective binding of the nanoparticles via the cis-diol groups in the PGMA stabilizer chains, as judged by AFM studies. Control experiments confirmed that minimal selective nanoparticle binding occurred at pH 4, or if the PGMA 51 stabilizer block was replaced with a poly(ethylene glycol) PEG 113 stabilizer block.

A new cysteine-based methacrylic monomer (CysMA) was conveniently synthesized via selective thia-Michael addition of a commercially available methacrylate-acrylate precursor in aqueous solution without recourse to protecting group chemistry. Poly(cysteine methacrylate) (PCysMA) brushes were grown from the surface of silicon wafers by atom-transfer radical polymerization. Brush thicknesses of ca. 27 nm were achieved within 270 min at 20 °C. Each CysMA residue comprises a primary amine and a carboxylic acid. Surface zeta potential and atomic force microscopy (AFM) studies of the pH-responsive PCysMA brushes confirm that they are highly extended either below pH 2 or above pH 9.5, since they possess either cationic or anionic character, respectively. At intermediate pH, PCysMA brushes are zwitterionic. At physiological pH, they exhibit excellent resistance to biofouling and negligible cytotoxicity. PCysMA brushes undergo photodegradation: AFM topographical imaging indicates significant mass loss from the brush layer, while XPS studies confirm that exposure to UV radiation produces surface aldehyde sites that can be subsequently derivatized with amines. UV exposure using a photomask yielded sharp, well-defined micropatterned PCysMA brushes functionalized with aldehyde groups that enable conjugation to green fluorescent protein (GFP). Nanopatterned PCysMA brushes were obtained using interference lithography, and confocal microscopy again confirmed the selective conjugation of GFP. Finally, PCysMA undergoes complex base-catalyzed degradation in alkaline solution, leading to the elimination of several small molecules. However, good long-term chemical stability was observed when PCysMA brushes were immersed in aqueous solution at physiological pH.

A quantitative investigation of the responses of surface-grown biocompatible brushes of poly(2-(methacryloyloxy)ethyl phosphorylcholine) (PMPC) to different types of salt has been carried out using ellipsometry, quartz crystal microbalance (QCM) measurements, and friction force microscopy. Both cations and anions of varying valency over a wide range of concentrations were examined. Ellipsometry shows that the height of the brushes is largely independent of the ionic strength, confirming that the degree of swelling of the polymer is independent of the ionic character of the medium. In contrast, QCM measurements reveal significant changes in mass and dissipation to the PMPC brush layer, suggesting that ions bind to phosphorylcholine (PC) groups in PMPC molecules, which results in changes in the stiffness of the brush layer, and the binding affinity varies with salt type. Nanotribological measurements made using friction force microscopy show that the coefficient of friction decreases with increasing ionic strength for a variety of salts, supporting the conclusion drawn from QCM measurements. It is proposed that the binding of ions to the PMPC molecules does not change their hydration state, and hence the height of the surface-grown polymeric brushes. However, the balance of the intra- and intermolecular interactions is strongly dependent upon the ionic character of the medium between the hydrated chains, modulating the interactions between the zwitterionic PC pendant groups and, consequently, the stiffness of the PMPC molecules in the brush layer.

No abstract

Colorimetric aptasensors based on gold nanoparticles (AuNPs) commonly feature ssDNA probes nonspecifically adsorbed to surface gold particles. A major limitation of this versatile method is the incomplete dissociation of the adsorbed nontarget binding segments of the aptamer sequence upon target binding. This results in weak or nonexistent sensor performance by preventing the particles from aggregating when the optimized salt concentration is added. Rather than removing the nonbinding nucleotides flanking the binding region of the aptamer, proposed herein is an alternative strategy, simply introducing a centrifugation and resuspension step after target recognition that eliminates residual binding between the aptamer and the surface of the particles. The performance of two different vitamin D3 (VTD3) aptamers were tested. The method enhanced the performance of the sensor that used the higher detection limit (1 µM) aptamer by fourfold. The superiority of the proposed method became apparent in a nonworking colorimetric sensor became a highly sensitive sensor with a one nanomolar detection level and excellent discrimination against potential interfering molecules including VTD2 when the centrifugation and resuspension process was implemented. The level of VTD3 in human blood was determined colorimetrically after extraction with n-hexane. The results were in agreement with those obtained by HPLC. The proposed method could be applied to aptamers targeting small molecules with no need to reprocess the SELEX-isolated sequence by knowing the binding region and removing the flanking primers.