No abstract

Vertical stress is one of the three principal stresses and is an important parameter in geomechanical studies that are focussed on the prediction of pore pressure, fracture gradients and wellbore stability. Variations of the vertical stress magnitude can be attributed to variations in lithology or diagenetic history, localised uplift and overpressures caused by disequilibrium compaction. This study uses wellbore data from 102 open-file petroleum wells to characterise vertical stress within the onshore Canning Basin of north-western Australia. Vertical stress magnitudes are interpreted from density logs and checkshot data and at 1 km depth below the ground surface range from 20.5 to 25.0 MPa km–1 with a mean value of 22.1 MPa km–1 (s.d. = 1.0 MPa km–1). Significant variation is evident within the calculated stress magnitudes, and when presented spatially, three regions of elevated vertical stress are identified: the Barbwire Terrace, the Devonian reef complexes of the northern Lennard Shelf and the Mowla Terrace. Lithology, abnormal pore pressures and tectonic uplift are investigated as potential mechanisms of the observed variation. Although abnormal pore pressures are identified, no direct correlation between overpressured areas and elevated vertical stress magnitudes is observed. The Canning Basin has an extensive history of uplift; however, there is little evidence for significant recent inversion. While uplift is likely to exert some influence over vertical stress magnitudes in the Canning Basin, the primary cause is interpreted to be lithological: areas of elevated vertical stress magnitude are also areas where thick intervals of carbonate sediments are present.

No abstract

No abstract

Understanding natural fracture networks has increasingly been recognised as an important factor for the prospectivity of a geothermal play, as they commonly exert a prime control over permeability at depth. The onshore Northern Perth Basin provides a good example of how fracture stimulation, and subsequent enhancement of the structural permeability, during hydrocarbon production can enhance flow rate from original tight gas reservoirs. Low primary porosity and permeability values have been initially recorded in the Northern Perth Basin due to silica-rich groundwater infiltration and consequent quartz cementation. Geothermal energy prospectivity in the region will therefore depend heavily on similar engineering techniques or on the presence of secondary permeability due to interconnected natural fractures. The existence and extent of these natural fractures are verified in this study through an integrated analysis of geophysical logs (including wellbore image logs), wells tests, and 3D seismic data. Wellbore image logs from 11 petroleum wells in the Northern Perth Basin are used to identify borehole failure (such as borehole breakout and drilling-induced tensile fractures) to give a present-day maximum horizontal stress orientation of N076°E (with an s.d. of 13°). Density logs and leak off tests from 13 petroleum wells are used to constrain the present-day stress magnitudes, giving a transitional strike-slip fault to reverse-fault stress regime in the Northern Perth Basin. 870 fractures are identified in image logs from 13 petroleum wells in the Northern Perth Basin, striking roughly north to south and northwest to northeast. Fractures aligned in the present-day stress field are optimally oriented for reactivation, and are hence likely to be open to fluid flow. Electrically resistive and conductive natural fractures are identified on the wellbore image logs. Resistive fractures are considered to be cemented with electrically resistive cement (such as quartz or calcite) and thus closed to fluid-flow. Conductive fractures are considered to be uncemented and open to fluid-flow, and are thus important to geothermal exploration. Fracture susceptibility diagrams constructed for the identified fractures illustrate that the conductive fractures are optimally oriented for reactivation in the present-day strike-slip fault to reverse-fault stress regime, and so are likely to be open to fluid flow. This is reinforced by the correlation of drilling fluid loss and conductive natural fractures in three wells in the Northern Perth Basin. To gain an understanding of the extent and interconnectedness of these fractures, it is necessary to look at more regional data, such as 3D seismic surveys. It is, however, well-documented that fault and fracture networks like those generally observed in image logs lie well below seismic amplitude resolution, making them difficult to observe directly on amplitude data. Seismic attributes can be calculated to provide some information on sub-seismic scale structural and stratigraphic features. Using a 3D seismic cube acquired over the Dongara North gas field, attribute maps of complex multi-trace dip-steered coherency and most positive curvature were used to document the presence of natural fractures and to best constrain the likely extent of the fracture network. The resulting fracture network model displays relatively good connectivity, which is likely to extend across much of the basin. These optimally oriented fractures are therefore likely to form a secondary permeability network throughout the cemented sediments of the Northern Perth Basin, offering potential deep fluid flow conduits, which may be exploited for the production of geothermal energy.