23.06.14 KB. Ok to add accepted version to spiral, Elsevier says ok while mandate not enforced

Existing cross-section and member buckling test data on CHS were collected;  Numerical simulation was conducted to generate further data on CHS;  New design rules were developed to capture the elasto-plastic behaviour of semi-compact CHS;  Accuracy of the current Eurocode 3 and proposed methods were assessed and compared;  Reliability of the proposed design rules was confirmed through statistical analyses.

An analytical model describing the nonlinear interaction between global and local buckling modes in long thin-walled rectangular hollow section struts under pure compression founded on variational principles is presented. A system of nonlinear differential and integral equations subject to boundary conditions is formulated and solved using numerical continuation techniques. For the first time, the equilibrium behaviour of such struts with different cross-section joint rigidities is highlighted with characteristically unstable interactive buckling paths and a progressive change in the local buckling wavelength. With increasing joint rigidity within the cross-section, the severity of the unstable post-buckling behaviour is shown to be mollified. The results from the analytical model are validated using a nonlinear finite element model developed within the commercial package Abaqus and show excellent comparisons. A simplified method to calculate the local buckling load of the more compressed web undergoing global buckling and the corresponding global mode amplitude at the secondary bifurcation is also developed. Parametric studies on the effect of varying the length and cross-section aspect ratio are also presented that demonstrate the effectiveness of the currently developed models.

This paper explores the use of solid continuum finite elements and shell finite elements in the modelling of the nonlinear plastic buckling behaviour of cylindrical metal tubes and shells under global bending. The assumptions of shell analysis become increasingly uncertain as the ratio of the radius of curvature to the thickness becomes smaller, but the classical literature does not draw a clear line to define when a shell treatment is inappropriate and a continuum model becomes essential. This is a particularly important question for the bending of tubular members, pipelines, chimneys, piles, towers and similar structures. This study is therefore concerned solely with the uniform bending of thin tubes or thick shells which fail by plastic buckling well into the strain-hardening range. The analyses employ finite element formulations available in the commercial software ABAQUS because this is the most widely used tool for parametric research studies in this domain with an extensive and diverse element library. The results are of general validity and are applicable to other finite element implementations. This paper thus seeks to determine the adequacy of a thin or thick shell approximation, taking into account geometric nonlinearity, complex equilibrium paths, limit points and bifurcation buckling, extensive material ductility and linear strain hardening. It aims to establish when it is viable to employ shell elements and when this decision will lead to outcomes that lack sufficient precision for engineering design purposes. Sciences, 74, 143-153. DOI: http://dx.doi.org/10.1016/j.ijmecsci.2013 continuum elements to model tubes in bending is found to become increasingly uneconomical as the R/t ratio rises above 25 with reduced advantages over shell elements, both in terms of the accuracy of the solution and the computation time.

The new Reference Resistance Design (RRD) method, recently developed by Rotter [1], for the manual dimensioning of metal shell structures effectively permits an analyst working with only a calculator or spreadsheet to take full advantage of the realism and accuracy of an advanced nonlinear finite element (FE) calculation. The method achieves this by reformulating the outcomes of a vast programme of parametric FE calculations in terms of six algebraic parameters and two resistances, each representing a physical aspect of the shell's behaviour. The formidable challenge now is to establish these parameters and resistances for the most important shell geometries and load cases. The systems that have received by far the most research attention for RRD are that of a cylindrical shell under uniform axial compression and uniform bending. Their partial algebraic characterisations required thousands of finite element calculations to be performed across a four-dimensional parameter hyperspace (i.e. length, radius to thickness ratio, imperfection amplitude, linear strain hardening modulus). Handling so many nonlinear finite element models is time-consuming and the quantities of data generated can be overwhelming. This paper illustrates a computational strategy to deal with both issues that may help researchers establish sets of RRD parameters for other important shell systems with greater confidence and accuracy. The methodology involves full automation of model generation, submission, termination and processing with object-oriented scripting, illustrated using code and pseudocode fragments