Summary The 3D hydraulic-fracture-simulation modeling was integrated with 4D time-lapse seismic and microseismic data to evaluate the efficiency of hydraulic-fracture treatments within a 1 sq mile well-spacing test of Wattenberg Field, Colorado. Eleven wells were drilled, stimulated, and produced from the Niobrara and Codell unconventional reservoirs. Seismic monitoring through 4D time-lapse multicomponent seismic data was acquired by prehydraulic fracturing, post-hydraulic fracturing, and after 2 years of production. The results from the simulation modeling and seismic monitoring show the significant effect of reservoir heterogeneity on hydraulic-fracture stimulation and hydrocarbon production. A hydraulic-fracture-simulation model using a 3D numerical simulator was generated and analyzed for hydraulic-fracturing efficiency and interwell fracture interference between the 11 wells. The 3D hydraulic-fracture simulation is validated using observations from microseismic and 4D multicomponent [compressional-wave (P-wave) and shear-wave (S-wave)] seismic interpretations. The validated 3D simulation results reveal that variations in reservoir properties (faults, rock-strength parameters, and in-situ stress conditions) influence and control hydraulic-fracturing geometry and stimulation efficiency. The integrated results are used to optimize the development of the Niobrara Formation within Wattenberg Field. The valuable insight obtained from the integration is used to optimize well spacing, increase reserves recovery, and improve production performance by highlighting intervals with bypassed potential within the Niobrara. The methods used within the case study can be applied to any unconventional reservoir.

With Saudi Aramco's recent ambitious endeavors toward exploring unconventional resources in the Kingdom, the Unconventional Resources Program at Saudi Aramco has adopted a robust technology – microseismic monitoring – that pinpoints where hydraulic fractures are induced. Microseismic monitoring is a relatively new technology to Saudi Aramco for monitoring hydraulic fracturing. Microseismic events can pinpoint where the formation is sheared and can detect events to show excessive downward growth. Also, it can identify the occurrence and the azimuths of faults and natural fractures. After analyzing the results from a well in a Saudi unconventional play, microseismic monitoring resulted in revising future fracturing designs. The fracturing treatment in the subject well was designed for a crosslinked fluid, creating excessive downward growth. Therefore, the team believes a slickwater treatment would be preferred to stay in the zone. Also, faults and natural fractures were observed around a stimulated area. Therefore, future fracture treatments will be placed away from these faulted and fractured areas to capitalize on stimulating the pay zone. Microseismic monitoring has played a key role in optimizing upcoming fracture treatments, which in turn will affect future field development strategies, especially for unconventional plays. It is worth noting that this was the first time a horizontal well was used for microseismic monitoring for another horizontal well in Saudi Arabia.

No abstract

3D hydraulic fracture simulation modeling integrated with 4D time-lapse seismic and microseismic data were used to evaluate the efficiency of hydraulic fracture treatments in a one square mile spacing test within Wattenberg Field, Colorado. The study was conducted over a section within Wattenberg Field containing eleven horizontal wells that were hydraulically fracture stimulated and produced. The 4D time- lapse multicomponent seismic data were acquired pre-hydraulic fracturing, post-hydraulic fracturing, and after two years of production. The 3D simulation results integrated with and dynamic seismic observations are used to analyze the effect of geological heterogeneity on hydraulic fracturing efficiency and hydrocarbon production. A 3D geomechanical model was generated using geostatistical methods as an input to hydraulic fracture simulation and incorporated the faults and the lithological changes in the study area. The 3D geomechanical model was calibrated through the use of DFIT data from offset wells. A hydraulic fracture simulation model using a 3D numerical simulator was generated and analyzed for hydraulic fracturing efficiency and interwell fracture interference between the eleven wells. The 3D hydraulic fracture simulation is validated using observations from microseismic and 4D multicomponent (P-wave and S- wave) seismic interpretations. The validated 3D simulation results provide insight into the effect of geological heterogeneity on the hydraulic fracturing efficiency by providing information relative to the induced fracture lengths, resultant effective fracture lengths and established fracture conductivity. The 3D simulation result and dynamic seismic interpretations both reveal that variations in reservoir properties (faults, rock strength parameters, and in-situ stress conditions) influence and control hydraulic fracturing geometry and stimulation efficiency. Microseismic data is observed to capture hydraulic fracture lengths over 1000 ft. This was also confirmed using tracer analysis. The P-wave time-lapse seismic response from hydraulic fracturing is shown to be affected by pressure pulses created from stimulating the reservoir. The 4D P-wave response is indicative of the presence of pressure compartmentalization caused by fault barriers within the reservoir. The P-wave response also confirms the results from the 3D hydraulic fracture simulation demonstrating an effective stress barrier above the Niobrara formation which allows hydraulic fracture containment to occur. Shear wave (S-wave) time- lapse seismic data are shown to provide a close estimate for effective fracture lengths that result from hydraulic fracturing based on a successful match to the simulation results. The effective fracture length is defined as the propped fracture length that provides communication with the wellbore during the production cycle. Through this integrated 3D hydraulic fracture simulation modeling more confidence is placed on results from the simulation as a guide for further optimizing the development of the Niobrara Formation within the Wattenberg Field. The integrated analysis provides valuable insight into optimizing well spacing, increasing recovery and improving production performance in the Niobrara, as well as highlighting intervals with bypassed potential within the reservoir.

Enhanced hydrocarbon recovery is essential for continued economic development of unconventional reservoirs. Our study focuses on dynamic characterization of the Niobrara and Codell Formations in Wattenberg Field through the development and analysis of a full integrated reservoir model. We demonstrate the effectiveness of hydraulic fracturing and production with two seismic monitor surveys, surface microseismic, completion data, and production data. The two monitor surveys were recorded after stimulation, and again after two years of production. Identification of reservoir deformation due to hydraulic fracturing and production improves reservoir models by mapping non-stimulated and non-producing zones. Monitoring these time-variant changes improves the prediction capability of reservoir models, which in turn leads to improved well and stage placement. We quantify dynamic reservoir changes with time-lapse P-wave seismic data utilizing pre-stack inversion, and velocity-independent layer stripping for velocity and attenuation changes within the Niobrara and Codell reservoirs. A 3D geomechanical model and production data are history matched, and a simulation is run for two years of production. Results are integrated with time-lapse seismic data to illustrate the effects of hydraulic fracturing and production. Our analyses illustrate that chalk facies have significantly higher hydraulic fracture efficiency and production performance than marl facies. Additionally, structural and hydraulic complexity associated with faults generate spatial variability in a well’s total production.