Pristine halloysite nanotubes (HNTs) were pretreated to produce mesoporous silica nanotubes (MSiNTs), which was further impregnated with polyethenimine (PEI) to prepare an emerging nanocomposite MSiNTs/PEI (MP) for CO2 capture. Thermogravimetric analysis (TGA) was employed to analyze the influences of PEI loading amount and adsorption temperature on CO2 adsorption capacity of the nanocomposite. The Brunauer-Emmett-Teller (BET) surface area (SBET) of MSiNTs was six times higher than that of HNTs, and the corresponding pore volume was more than two times higher than that of HNTs. The well dispersion of PEI within the nanotubes of MSiNTs benefits more CO2 gas adsorption, and the adsorption capacity of the nanocomposite could reach 2.75 mmol/g at 85 °C for 2 h. The CO2 adsorption on the nanocomposite was demonstrated to occur via a two-stage process: initially, a sharp linear weight increase at the beginning, and then a relatively slow adsorption step. The adsorption capacity could reach as high as 70% within 2 min. Also, the nanocomposite exhibited good stability on CO2 adsorption/desorption performance, indicating that the as-prepared emerging nanocomposite show an interesting application potential in the field of CO2 capture.

No abstract

A novel two-step approach was developed to fabricate well-dispersed Na 1.08 V 3 O 8 nanosheets, which consist of ultra-thin monolayer sheets with a thickness of ca. 10 nm. The formation mechanism of nanosheets involves the fusion and conversion of nanorods. When used as a cathode material for Li-ion batteries, the nanosheets show superior rate capability, with discharge capacities of ca. 200.0, 131.3, 109.9, 94.2 and 72.5 mA h g À1 at 0.4, 10, 20, 30 and 50 C, respectively. Excellent cycling stability without considerable capacity loss over 200 cycles is observed at 600 and 1000 mA g À1 . It is believed that the unique nanosheet morphology as well as its intrinsic structural features greatly facilitate the kinetics of Li-ion diffusion and excellent structure stability, thus resulting in superior electrochemical performance.

Both octahedral and slice-shaped cubic cobalt monoxide (CoO) nanocrystals with narrow size distributions have been successfully synthesized by a simple solvothermal route. It was found that conditions of the solvothermal treatment showed obvious effects on the formation and purity of the as-synthesized CoO nanocrystals, only when cobalt acetate was used as the cobalt source and when temperature reached 190 degrees C could CoO be produced; also, freeze-drying was necessary for obtaining pure CoO. Size of the CoO nanocrystals varied from 30 to 130 nm. Morphology of the products could be controlled by simply changing the type of surfactant in solvent, and the octahedral CoO nanocrystals showed rounded turns. Purity of the products was detected by intensive X-ray photoelectron spectroscopy (XPS) investigation and Fourier transform infrared spectroscopy (FTIR) combined with differential scanning calorimetry/thermal gravity (DSC/TG). The results indicated an absence of unexpected trivalence cobalt series on surface of the samples, thanks to the protection of the surface by trace amount of carbonate ions, adsorbed hydroxylation, and surfactant with a maximum thickness of 2 nm, which were proved by high-resolution transmission electron microscopy (HRTEM). The as-synthesized CoO nanoparticles were added into positive electrode of Ni/MH batteries, and discharge/charge cycling tests were performed under different rates from 0.1C to 5.0C. The results indicated that the specific capacities of batteries with addition of 5% octahedral or slice CoO nanocrystals at 0.1C were 393.3 and 318.1 mAh/g, respectively, which were higher than that without CoO (269.2mAh/g). Specific capacity of battery with addition of 5% octahedral CoO nanocrystals was 40% higher than that without CoO at 5.0C. Octahedral CoO nanocrystals show better electrochemical activity than slice CoO and indicate interesting potential in the field of electrochemical application.

No abstract