The determination of the authenticity of extra virgin olive oils (EVOOs) has become more interesting in recent years. Italy is the first country in Europe in terms of number of Protected Designation of Origin (PDO) oils, which connects consumers to a feeling of tradition and thus to higher quality standards. This work focused on the consideration of the inorganic content as a possible marker of EVOOs. Ten vegetable oils (VOs), eight Italian EVOOs and seven not Italian EVOOs were analyzed. After pretreatment by acid mineralization, Al, Ba, Ca, Cu, Fe, K, Li, Mg, Mn, Na, P, Sb, Se and Zn were determined by ICP-OES. The electrochemical properties of a selected group of EVOOs and other vegetal oils of different botanical origin were investigated by voltammetry. Carbon paste electrodes (CPEs) were prepared. The features observed in the voltammograms reflect the reactions of electroactive compounds, which are present in the oils. A chemometric treatment of the results was performed to assess the possibility to distinguish (i) the region of provenience considering the inorganic profile; and (ii) the plant species from which each oil was obtained on the basis of the current profile registered during voltammetric analysis. Inorganic composition seems to be a useful marker for the assessment of the geographical origin of an EVOO. The EVOO-CPEs voltammetry seems to have a good ability to distinguish the plant species of origin. This method could be useful to monitor the conservation status of the oils, as the redox profile is linked to the oxidative degradation state.

In this work, an evaluation of the air of two Italian industrial cities, Turin and Biella, has been performed to identify the main sources affecting its quality and to evaluate its evolution along 15 years. These two cities are placed at the border of the Po valley, one of the most polluted areas of Europe, and the automotive and textile industries have been their main economic sectors. The elemental analysis of the PM10 collected there in 2007 has been performed by ICP-MS and ICP-AES. The results identify the urban activities and the soil/road dust resuspension as the main sources of metals. Biella was overall less polluted in PM10 than Turin, probably because of its smaller size, its smaller traffic volume, and the lower number of industries. However, the limit value imposed by the European legislation for daily average PM10 mass concentration (50 μg m−3) was frequently exceeded in the collected samples: 22% and 50%, respectively for Biella and Turin. The concentration of specific toxic metals regulated by Italian legislation was never higher than the limit value for Cd (4 ng m−3) and Pb (0.5 μg m−3), whereas it was exceeded for Ni (20 ng m−3) in 22% of the samples from Turin and only in the 5% of those from Biella. In the same way, the risk analysis, performed using the target hazard quotient (THQ), calculated for children and adult populations, did not reveal warning values. Only for Cd in children were concerning values found (median THQ = 4.9). Element concentrations showed a seasonal trend, with higher values in November and December due to a combination of stable atmospheric conditions and strengthening of anthropic sources (e.g., combustion for heat generation). Finally, data concerning the amount of Cd, Ni, and Pb in the atmosphere provided by the regional agency for environmental protection (ARPA Piedmont) have been used to follow the evolution of these elements from 2007 to 2021 in the two cities. The data reveal a significant reduction of the concentrations of all considered metals in all the sites (higher than 50%), however maintaining the seasonal variability observed in PM10 samples of 2007, with higher concentrations during the cold months and lower concentrations during the summer.

Mercury (Hg) and its compounds are highly toxic for humans and ecosystems, and their chemical forms determine both their behavior and transportation as well as their potential toxicity for human beings. Determining the various species of an element is therefore more crucial than understanding its overall concentration in samples. For this reason, several studies focus on the development of new analytical techniques for the identification, characterization, and quantification of Hg compounds. Commercially available, hyphenated technology, such as HPLC-ICP-MS, supports the rapid growth of speciation analysis. This review aims to summarize and critically examine different approaches for the quantification of mercury species in different samples using HPLC-ICP-MS. The steps preceding the quantification of the analyte, namely sampling and pretreatment, will also be addressed. The scenarios evaluated comprehend single and multi-element speciation analysis to create a complete guide about mercury content quantification.

Aluminium is the most common substrate in studies using impactors for the measurement of the number or the weight of size-segregated atmospheric particulate matter (PM), as its characteristics perfectly fit impactor requirements. However, its use is not recommended by manufacturers when one of the purposes of the study is the determination of the metal content in the sample. The aim of this work was to develop an efficient analytical procedure for the removal and acid digestion of PM samples collected on aluminium foils by a cascade impactor to perform the determination of metals. The possibility of performing the trace metal analysis of PM samples collected using aluminium foils is of great importance, as it allows the determination of an accurate size distribution and the elemental composition of the PM collected on each impactor stage. Two procedures were optimised by using different digestion and analysis techniques. Both procedures were then applied to the two halves of several Dekati low-pressure impactor (DLPI) samples, and the results were critically compared. The two procedures proved to be effective in the determination of extremely low concentrations of a large suite of analytes in different size fractions of PM emitted by a brake system.