An in-depth investigation on novel electro-activated shape memory polymer composites (SMPCs) for digital light processing 3D-Printing, consisting of a poly(ethylene glycol) diacrylate/poly(hydroxyethyl methacrylate) matrix embedding multi-walled carbon nanotubes (CNTs), is reported here. The composition of the photocurable (meth)acrylate system is finely tuned to tailor the thermomechanical properties of the matrix, whereas the effect of CNTs on the photoreactivity and rheological properties of the formulations is investigated to assess the printability. Electrical measurements confirmed that the incorporation of CNT into the polymeric matrix enables the electrical conductivity and thus the possibility to remotely heat the nanocomposite using the Joule effect. The feasibility to drive a shape memory cycle via Joule heating is proved, given that the high shape fixity (R f ) and shape recovery (R r ) ratios achieved (R f ≈ 100%, R r > 95%) confirmed the significant electrically-triggered responsiveness of such CNT/SMPCs. Finally, it is shown how to activate a modular and selective electro-activated shape recovery, which may ultimately envisage the 4D-Printing of remotely and selectively controllable smart devices.

Mechanical and strain sensing capabilities of carbon nanotube (CNT) reinforced composites manufactured by digital light processing (DLP) 3D printing technology have been studied. Both CNT content and a post-curing treatment effects have been analyzed. It has been observed that post-curing treatment has a significant influence on mechanical properties, with an increase of Young’s modulus and glass transition temperature whereas their effect in electrical properties is not so important. Furthermore, the strain sensing tests show a linear response of electrical resistance with applied strain, with higher values of sensitivity when decreasing CNT content due to a higher interparticle distance. Moreover, the electrical sensitivity of bending tests is significantly lower than in tensile ones due to the compression subjected face effect. Therefore, the good gauge factor values (around 2–3) and the high linear response proves the applicability of the proposed nanocomposites in structural health monitoring applications.

Nowadays, there is an important concern in the scientific community related to the end-of-life products derived from polymeric matrix composites. In this regard, covalent adaptable networks and, more specifically, the disulfide bond-based ones are a promising approach to develop composite parts able to be dissolved in a specific solvent, thus regaining the continuous fiber reinforcement. In this work, the effect of hardener isomerism, using 2-aminophenyl disulfide (2-AFD) and 4-aminophenyl disulfide (4-AFD), and amine/epoxy ratio (1.0–1.2) was studied to optimize the chemical recycling capabilities at different temperatures. Results confirmed the need for using hardener excesses for dissolving these vitrimers. Networks based on 2-AFD were dissolved in considerably lower times than the 4-AFD ones, which is interesting since the latter one is quite more used for this purpose and currently way more expensive. In this context, a composite laminate, reinforced with six layers of carbon fiber fabric, was manufactured as the proof-of-concept.

No abstract

Electromechanical sensing devices, based on resins doped with carbon nanotubes, were developed by digital light processing (DLP) 3D printing technology in order to increase design freedom and identify new future and innovative applications. The analysis of electromechanical properties was carried out on specific sensors manufactured by DLP 3D printing technology with complex geometries: a spring, a three-column device and a footstep-sensing platform based on the three-column device. All of them show a great sensitivity of the measured electrical resistance to the applied load and high cyclic reproducibility, demonstrating their versatility and applicability to be implemented in numerous items in our daily lives or in industrial devices. Different types of carbon nanotubes—single-walled, double-walled and multi-walled CNTs (SWCNTs, DWCNTs, MWCNTs)—were used to evaluate the effect of their morphology on electrical and electromechanical performance. SWCNT- and DWCNT-doped nanocomposites presented a higher Tg compared with MWCNT-doped nanocomposites due to a lower UV light shielding effect. This phenomenon also justifies the decrease of nanocomposite Tg with the increase of CNT content in every case. The electromechanical analysis reveals that SWCNT- and DWCNT-doped nanocomposites show a higher electromechanical performance than nanocomposites doped with MWCNTs, with a slight increment of strain sensitivity in tensile conditions, but also a significant strain sensitivity gain at bending conditions.