In this article, technology for producing wire and rod solder from 52In-48Sn alloy has been developed and investigated in the conditions of small-scale production. The use of direct extrusion of wire and rods instead of traditional technology for producing solder, which includes pressing, rolling and drawing, can significantly reduce the fleet of required equipment. Using only a melting furnace and a hydraulic press, solder wires and rods can be produced in various sizes. Shortening the production cycle allows you to quickly fulfill small orders and be competitive in sales. This article develops a mathematical model of direct extrusion, which allows you to calculate the extrusion ratio, extrusion speed and pressing force. The results of modeling the process of extrusion of wire Ø2.00 mm and rods Ø8.0 mm made of 52In-48Sn alloy are presented. The temperature of the solder and the tool is simulated in software QForm based on the finite element method. Experimental results of manufacturing Ø2.0 mm solder wire and Ø8.0 mm rods are presented. The microstructure of the direct extruded solder is a eutectic of phases γ and β. Energy-dispersive X-ray spectroscopy (EDS) mapping of the 52In-48Sn alloy showed that the solder obtained by direct extrusion has a uniform distribution of structural phases. The developed technology can be used in the manufacture of wires and rods from other low-melting alloys.
This paper presents the results of a study of changes in mechanical properties, namely tensile strength, yield strength and elongation when drawing a wire from NP2 nickel (Ni 99.6). The wire samples taken along the drawing route were tested for tension. Based on the test results obtained, graphs of changes in tensile strength, yield strength and elongation were plotted depending on cold work. The approximation of the graphs made it possible to obtain equations for the change in tensile strength (UTS), yield strength (0.2 US) and elongation (δ) depending on cold work (ɛ∑). The obtained dependences are recommended to be used to predict the mechanical properties of nickel wire during drawing and when developing software for designing resource-saving drawing routes.
In this article, a technology for producing wire and rod solder from 52In-48Sn alloy has been developed and investigated in the conditions of small-scale production. The use of direct extrusion of wire and rods instead of the traditional technology for producing solder, which includes pressing, rolling and drawing, can significantly reduce the fleet of required equipment. Using only a melting furnace and a hydraulic press, solder wires and rods can be produced in various sizes. Shortening the production cycle allows you to quickly fulfill small orders and be competitive in sales. The article developed a mathematical model of direct extrusion, which allows you to calculate: extrusion ratio, extrusion speed and pressing force. The results of modeling the process of extrusion of wire ∅2.00 mm and rods ∅8.0 mm made of 52In-48Sn alloy are presented. The temperature of the solder and the tool is simulation in software QForm based on the finite element method. Experimental results of manufacturing ∅2.0 mm solder wire and ∅8.0 mm rods are presented. The microstructure of the direct extruded solder is a eutectic of phases γ and β. Energy-dispersive X-ray spectroscopy (EDS) mapping of the 52In-48Sn alloy showed that the solder obtained by direct extrusion has a uniform distribution of structural phases. The developed technology can be used in the manufacture of wires and rods from other low-melting alloys.
In this article, a mathematical model of the wire’s average temperature change in the process of multiple drawing on high-speed straight-line drawing machines has been developed. The calculation results showed that the average temperature of the wire during a drawing at a speed of up to 45 m/s on straight-line drawing machines could reach 400 °C. Deformation heating of the wire during drawing does not exceed 60 °C, and heating due to sliding friction can reach 300 °C, depending on the friction coefficient, which ranges from 0.05 to 0.15. The average strain rates under the conditions of the modern high-speed drawing process reach 7000 s−1. Over the course of the research, it was found that there are no conditions for the occurrence of dynamic deformation aging due to impurity atoms of carbon, nitrogen and oxygen. At the same time, at the temperature and speed parameters of the high-speed wire drawing, conditions are created for the onset of the dynamic strain aging of steel in the presence of hydrogen atoms. Therefore, during heat treatment and pickling, it is necessary to exclude the hydrogenation of steel. It has been established that in order to exclude static strain aging of steel during drawing, it is necessary to prevent heating the wire above 180–200 °C.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.