No abstract

Biodiesel is considered a promising replacement to petroleum-derived diesel. Using oils extracted from agricultural crops competes with their use as food and cannot realistically satisfy the global demand of diesel-fuel requirements. On the other hand, microalgae, which have a much higher oil yield per hectare, compared to oil crops, appear to be a source that has the potential to completely replace fossil diesel. Microalgae oil extraction is a major step in the overall biodiesel production process. Recently, supercritical carbon dioxide (SC-CO2) has been proposed to replace conventional solvent extraction techniques because it is nontoxic, nonhazardous, chemically stable, and inexpensive. It uses environmentally acceptable solvent, which can easily be separated from the products. In addition, the use of SC-CO2 as a reaction media has also been proposed to eliminate the inhibition limitations that encounter biodiesel production reaction using immobilized enzyme as a catalyst. Furthermore, using SC-CO2 allows easy separation of the product. In this paper, conventional biodiesel production with first generation feedstock, using chemical catalysts and solvent-extraction, is compared to new technologies with an emphasis on using microalgae, immobilized lipase, and SC-CO2 as an extraction solvent and reaction media.

Various beneficial properties has been attributed to Nigella sativa, including its antioxidant potential. Previously, it was reported that supercritical fluid extraction (SFE) could be used to obtain N. sativa extract rich in antioxidants. In the present study, N. sativa extracts prepared using the previously optimized SFE as well as the traditional Soxhlet extraction approaches were analyzed for various known antioxidants. N. sativa extracts were found to prevent protein carbonyl formation as well as depletion of intracellular glutathione (GSH) in fibroblasts exposed to toluene. Furthermore, partially purified SFE and Soxhlet fractions could prevent loss of hepatic GSH in toluene-induced oxidative stressed Wistar rats as well as in L929 fibroblasts. The results showed that SFE-produced N. sativa extract is richer in antioxidants than the Soxhlet approach. It was also shown using preparative silica gel and reverse phase chromatography that different fractions of SFE-extracted or Soxhlet-extracted N. sativa had different levels of protective effects with regards to GSH depletion in vivo as well as in cell culture. Although fractions rich in thymoquinone were found to be most potent in terms of antioxidant capacity, the data indicates that the protective effects of N. sativa may not only be due to thymoquinone, but perhaps other antioxidants.

Towards the utilization of different parts of date palm biomass waste, low-concentration acid-alkali treatment was used to isolate the contained cellulose and α-cellulose. The cellulose yields achieved from the rachis, leaflet, and fiber parts of the biomass were 74.70%, 71.50%, and 73.82%, respectively, while the corresponding α-cellulose yields were 78.63%, 75.64%, and 70.40%, respectively. The cellulose samples were bleached and characterized by thermogravimetric analysis (TGA), Fourier-transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD). The XRD results revealed high crystallinity of both the cellulose and α-cellulose samples, while the TGA thermograms indicated that the alkali treatment completely removed lignin and hemicelluloses from the rachis. The results of this study demonstrate the promise of using date palm biomass waste as raw material to produce cellulose and α-cellulose.

Due to the significant properties of silica, thermostatics can be enhanced using silica-additives to maximize the quality of polymer compounds and transform plastics into tailored properties. The silica additives can enhance the handling and quality performance of composites and thermoplastic polymers due to their diverse potential. Besides, using silica as an additive in different characteristics can allow granulates and powders to flow easily, minimize caking, and control rheology. On the other hand, the eruption of 3D printing technology has led to a massive new waste source of plastics, especially the polylactic acid (PLA) that is associated with the fused deposition modeling (FDM) process. In this paper, the impact on the mechanical properties when silica is mixed with waste PLA from 3D printing was studied. The PLA/silica mixtures were prepared using different blends through twin extruders and a Universal Testing Machine was used for the mechanical characterization. The result indicated that increasing silica composition resulted in the increase of the tensile strength to 121.03 MPa at 10 wt%. Similar trends were also observed for the toughness, ductility, and the yield stress values of the PLA/silica blends at 10 wt%, which corresponds to the increased mechanical property of the composite material reinforced by the silica particles. Improvement in the mechanical properties of the developed composite material promotes the effective recycling of PLA from applications such as 3D printing and the potential of reusing it in the same application.