A geophysical investigation was carried out after the failure of an important railway embankment in the south-east of Ireland. The embankment, which had a long-term history of stability problems, was studied using a combination of ground-penetrating radar (GPR), electrical resistivity tomography (ERT), multichannel analysis of surface waves (MASW) and geotechnical testing. A significant thickening of the ballast layer around the failure location was observed using GPR, which confirmed the existence of an ongoing stability problem in the area. ERT profiles determined the presence and spatial extent of a significant layer of soft clay both beneath and to the east of the embankment, which could have a major impact on its long-term stability. ERT also detected steeply sloping bedrock close to the failure zone that is likely to have contributed to the long-term settlement of the embankment, which necessitated frequent re-ballasting. MASW confirmed the presence of the steeply sloping bedrock in addition to determining the low stiffness (G max ) values of the embankment fill.High quality sampling of the soft clay deposit was undertaken and strength and compressibility tests revealed the importance of this layer to both the on-going serviceability problems evident for the original embankment and the stability problems encountered by the remodelled section.

Abstract:The paper set out two techniques to model the Cone Penetration Test (CPT) end resistance, q c in a dense sand deposit using commercial finite element programmes. In the first approach, Plaxis was used to perform spherical cavity expansion analyses at multiple depths. Two soil models, namely; the MohrCoulomb (MC) and Hardening Soil (HS) models were utilized. When calibrated using simple laboratory element tests, the HS model was found to provide good estimates of q c . However, at shallow depths, where the over-consolidation ratio of the sand was highest, the relatively large horizontal stresses prevented the full development of the failure zone resulting in under-estimation of the q c value. The second approach involved direct simulation of cone penetration using a large-strain analysis implemented in Abaqus/Explicit. The Arbitrary Lagrangian Eulerian (ALE) technique was used to prevent excessive mesh deformation. Although the Druker-Prager soil model used was not as sophisticated as the HS model, excellent agreement was achieved between the predicted and measured q c profiles.

This paper presents the results of compression and tension load tests performed on a single helical pile installed in dense sand. The pile was instrumented using strain gauges that allowed the shaft and base load resistance to be separated and the distribution of shaft resistance along the pile during the test to be determined. The pile was loaded first in compression, with a maintained load test, followed by a constant rate of penetration load test being performed to assess the effects of creep on the pile’s response to compression loading. The pile was then loaded in tension using a maintained load test procedure. Finite element analyses were performed using Abaqus and these helped to provide additional insights to explain the response of the instrumented pile during loading. The test showed that during compression loading, substantial bearing pressures developed beneath the pile helix, which provided the majority of axial load resistance. During tension loading, uplift pressure mobilized on the helix again provided the majority of axial resistance. The strain gauges suggested that the pile load response to compression loading was ductile. During tension loading, the pile response was brittle. Whilst load tests performed on only one instrumented pile test are presented, the use of instrumentation and finite element analyses allowed important insights into the load–displacement response of helical piles.

No abstract

This paper presents the results of full-scale load tests performed to investigate the end bearing pressure mobilised by continuous flight auger piles installed in sand. In particular, the tests considered the effects of the footing width and, by varying the load test procedure (from maintained load test to constant rate of penetration), allowed quantification of creep effects. By comparing the load test results with in situ test results from cone penetration tests, correlations between the end bearing pressure mobilised at normalised settlement levels of 10% of the footing width and the cone penetration test qc value were studied. For the maintained load tests, these correlations were found to be similar to those used in routine design practice. When creep effects were reduced using constant rate of penetration load testing, the end bearing pressure mobilised was significantly higher than that assumed in normal practice, and it was in keeping with the results of finite-element analyses performed using a soil model that ignored creep. In the final section, the field test results are compared to database pile load tests performed on non-displacement piles in sand.