In view of a rapid development and increase in efficiency of organic solar cells, reaching their long‐term operational stability represents now one of the main challenges to be addressed on the way toward commercialization of this photovoltaic technology. However, intrinsic degradation pathways occurring in organic solar cells under realistic operational conditions remain poorly understood. The light‐induced dimerization of the fullerene‐based acceptor materials discovered recently is considered to be one of the main causes for burn‐in degradation of organic solar cells. In this work, it is shown that not only the fullerene derivatives but also different types of conjugated polymers and small molecules undergo similar light‐induced crosslinking regardless of their chemical composition and structure. In the case of conjugated polymers, crosslinking of macromolecules leads to a rapid increase in their molecular weight and consequent loss of solubility, which can be revealed in a straightforward way by gel permeation chromatography analysis via a reduction/loss of signal and/or smaller retention times. Results of this work, thus, shift the paradigm of research in the field toward designing a new generation of organic absorbers with enhanced intrinsic photochemical stability in order to reach practically useful operation lifetimes required for successful commercialization of organic photovoltaics.

Geopolymer (GP) composites show great potential as a replacement for ordinary Portland cement (OPC) in construction material, extrusion‐based, and additive manufacturing. The rheological properties of highly viscous and reinforced systems have not yet been well studied, due to limitations in the current state of the art rheometers and viscometers, such as size and torque limits. In this study, the basic rheological properties of highly reinforced, geopolymer composites with potential for 3D printing are innovatively investigated with “squeeze flow” and “flow table” tests commonly used in civil engineering. Squeeze‐flow rates of 0.1, 1.0, and 3.0 mm/s were assessed with varying sand weight percentages or basalt fiber lengths and compared to a conventional OPC mixture to differentiate the flow properties and deformation resistance of both materials. It is shown that the deformation resistance as a result of jamming increases with increasing solid reinforcement percentages, but that the overall effect of fiber size is somewhat inconclusive. In addition, the effect of squeeze‐flow rate exhibits an increase in load required to initiate flow at lower squeezing rates, but, upon reaching a certain ratio of solids to liquid in the matrix, the results become variable.

No abstract

The rheological properties of potassium‐based geopolymers were investigated through a series of experiments intended to isolate the influence of shear rate, recovery time, and shear ramping on thixotropy for a greater understanding of geopolymer thixotropic properties within the context of the geopolymer setting reaction. It is shown that for thixotropic disruption to occur a critical shear rate of 100 s−1 must be reached or surpassed, full thixotropic restructuring occurs at around 90–100 min of total undisturbed rest time, and that reaching a state of full thixotropic disturbance heavily depends on subjected processing parameters. In addition, a consistent crossover between the storage and loss modulus within 1–3 min of oscillation during cyclical oscillatory measurements greatly indicates the repeatability and reversibility of thixotropy in geopolymers and the potential for tailorable viscosity. Overall, it is found that geopolymer pastes exhibit strong evidence of thixotropy, which is favorable for additive manufacturing, and that allotted rest time before shear and shear rate greatly influence the overall rheological properties.

Geopolymers (GPs) are a class of amorphous, aluminosilicate-based ceramics that cure at room temperature. GPs are formed by mixing an aluminosilicate source, which is metakaolin in this case, with an alkali activator solution, which can be either sodium or potassium water glass. GPs have attracted interest for use in structural applications over the past few decades because they have superior mechanical properties to ordinary Portland cement (OPC). Additionally, they can tolerate much higher temperatures and produce a fraction of the CO₂ compared to OPC. This project aims to develop geopolymer composites for 4D printing (the fourth dimension being time) and test their mechanical properties. Rheology and the effects of curing in ambient conditions will be evaluated for fresh geopolymer. Freeze-thaw resistance will be evaluated on potentially printable composites for extreme temperature resistance, etc.