No abstract

The use of biosensors in point‐of‐care (POC) testing devices has attracted considerable attention in the past few years, mainly because of their high specificity, portability, and relatively low cost. Coupling these devices with miniaturized electrochemical transducers has shown great potential toward simple, rapid, and cost‐effective analysis that can be performed in the field, especially for healthcare, environmental monitoring, and food quality control. For this reason, the number of publications in this field has grown exponentially over the past decade, making it a trending topic in current research. Although great improvement has been achieved in the field of electrochemical biosensing, there are still some challenges to overcome, especially concerning the improvement of sensing materials and miniaturization. In this Review, we summarize some of the most recent advances achieved in POC electrochemical biosensor applications, focusing on new materials and modifiers for biorecognition developed to improve sensitivity, specificity, stability, and response time.

The surface microchemical environment of graphene oxide (GO) has so far been oversimplified for understanding practical purposes. The amount as well as the accurate identification of each possible oxygenated group on the GO surface are difficult to describe not only due to the complex chemical nature of the oxidation reactions but also due to several intrinsic variables related to the production and chemical processing of GO-based materials. However, to advance toward a more realistic description of the GO chemical environment, it is necessary to distinguish the oxygenated fragments with very peculiar characteristics that have so far been treated as simply graphene oxide. In this way, small oxidized graphitic fragments adsorbed on the GO surface, named oxidation debris or carboxylated carbonaceous fragments (CCFs), have been here separated from commercially available GO. Spectroscopy and microscopy results indicated that the chemical nature of these fragments is different from that of GO. By using the decoration of GO with silver nanoparticles as a conceptual model, it was seen that the presence of oxidation debris on the GO surface greatly influences the associated kinetic processes, mainly due to the nucleation and stabilization capacity for silver nanoparticles provided by the oxidation debris fragments. Consequently, when CCFs are present, Ag nanoparticles are significantly smaller and less crystalline. Considering the GO microchemical environment pointed out here, these findings can be qualitatively extrapolated to all other covalent and noncovalent functionalizations of GO.

Solid-state electrolytes based on ionic liquids and a gelling matrix are promising for rechargeable lithiumion batteries due to their safety under diverse operating conditions, favorable electrochemical and thermal properties, and wide processing compatibility. However, gel electrolytes also suffer from low mechanical moduli, which imply poor structural integrity and thus an enhanced probability of electrical shorting, particularly under conditions that are favorable for lithium dendrite growth. Here, we realize high-modulus, ion-conductive gel electrolytes based on imidazolium ionic liquids and exfoliated hexagonal boron nitride (hBN) nanoplatelets. Compared to conventional bulk hBN microparticles, exfoliated hBN nanoplatelets improve the mechanical properties of gel electrolytes by 2 orders of magnitude (shear storage modulus ∼5 MPa), while retaining high ionic conductivity at room temperature (>1 mS cm −1 ). Moreover, exfoliated hBN nanoplatelets are compatible with high-voltage cathodes (>5 V vs Li/Li + ) and impart exceptional thermal stability that allows high-rate operation of solid-state rechargeable lithium-ion batteries at temperatures up to 175 °C.

Background Methicillin-resistant Staphylococcus aureus (MRSA) has been responsible for serious hospital infections worldwide. Nanomaterials are an alternative to conventional antibiotic compounds, because bacteria are unlikely to develop microbial resistance against nanomaterials. In the past decade, graphene oxide (GO) has emerged as a material that is often used to support and stabilize silver nanoparticles (AgNPs) for the preparation of novel antibacterial nanocomposites. In this work, we report the synthesis of the graphene-oxide silver nanocomposite (GO-Ag) and its antibacterial activity against relevant microorganisms in medicine. Materials and methods GO-Ag nanocomposite was synthesized through the reduction of silver ions (Ag + ) by sodium citrate in an aqueous GO dispersion, and was extensively characterized using ultraviolet-visible absorption spectroscopy, X-ray diffraction, thermogravimetric analysis, X-ray photoelectron spectroscopy, and transmission electron microscopy. The antibacterial activity was evaluated by microdilution assays and time-kill experiments. The morphology of bacterial cells treated with GO-Ag was investigated via transmission electron microscopy. Results AgNPs were well distributed throughout GO sheets, with an average size of 9.4±2.8 nm. The GO-Ag nanocomposite exhibited an excellent antibacterial activity against methicillin-resistant S. aureus , Acinetobacter baumannii , Enterococcus faecalis , and Escherichia coli . All (100%) MRSA cells were inactivated after 4 hours of exposure to GO-Ag sheets. In addition, no toxicity was found for either pristine GO or bare AgNPs within the tested concentration range. Transmission electronic microscopy images offered insights into how GO-Ag nanosheets interacted with bacterial cells. Conclusion Our results indicate that the GO-Ag nanocomposite is a promising antibacterial agent against common nosocomial bacteria, particularly antibiotic-resistant MRSA. Morphological injuries on MRSA cells revealed a likely loss of viability as a result of the direct contact between bacteria and the GO-Ag sheets.