Introduction: Ectodermal dysplasia is an abnormality of the ectoderm and its derivatives, phenotypically expressed in males and genetically inherited from mothers. Objective: To report the efficacy of the prosthetics treatment of severe ectodermal dysplasia in a 6-year-old boy with hypohidrotic ectodermal dysplasia (HED). Case report: The boy had difficulty in speaking and eating and the condition also affected his self-esteem. Prosthetic treatments included the construction of acrylic custom trays, determination of the vertical dimension of occlusion (VDO), construction of upper and lower dentures, and palatal expansion procedure. Conclusion: Significant improvements in the patient's stomatognathic function and self-esteem were evident.

Aim: To introduce a modification of the reline impression technique (MRIT), and compare the dimensional changes of impressions obtained by MRIT and by conventional reline impression technique (CRIT). Methods: An acrylic resin tablet was milled by a CAD-CAM system to simulate three abutments (A, B and C) with different distances among them. The abutments were molded using both impression techniques. For MRIT, before completing the putty silicone polymerization, the relieve procedure was made by compression and it was immediately repositioned to complete the polymerization. Impressions were stored dry at room temperature for different periods (immediately, 1 h, 2 days and 7 days). The distances were obtained by scanning. The differences between the impressions and their respective matrix reference measurements were calculated to determine the dimensional changes. Data were subjected to ANOVA and Tukey's test (p<0.05). Results: For AB and BC distances, there was no statistically significant difference between CRIT and MRIT (p=0.0597 and p=0.2167, respectively). For AC, there was statistically significant difference between the techniques for the immediate storage time (p=0.006). In general, for CRIT the material showed expansion, while for MRIT it showed contraction. Conclusions: It was verified that the addition silicon impressions obtained by both impression techniques showed dimensional stability, except for the immediate time-point.

Aim: To evaluate the efficacy of ultrasonic bath and traditional brushing in the hygiene of complete dentures of dependent residents in long-term care institutions (LTCIs). Methods: A randomized cross-over clinical study was conducted in 17 maxillary complete denture wearers living in LTCIs. Cleaning protocols were brushing or ultrasonic bath, both applied with neutral liquid soap. Biofilm biomass were estimated by MTT reduction assay and specific microbial load (CFU) of Streptococcus spp., Staphylococcus spp. and Candida spp. were quantified by selective and differential culture media. Results: Ultrasound method showed higher percentage reduction of biofilm biomass and specific microbial loads of Streptococcus spp. compared to brushing (p<0.01). Reduction of microbial loads of the other microorganisms were not different between cleaning methods (p>0.05). Conclusions: The ultrasonic bath proved to be a feasible alternative method for the mechanical cleaning of complete dentures in LTCIs.

Most of techniques for determining the occlusal vertical dimension (OVD) of edentulous patients are based on soft tissues references, which lead to measurement discrepancies. Objective: To propose a method to obtain the OVD of edentulous patients during the confection of complete dentures considering the lower facial height established by Ricketts (LFHr) or the lower facial height obtained from cephalometric analysis of dentulous patients (LFHd). Material and methods: The OVD of 11 edentulous patients was determined by the association of 3 clinical methods. On each patient’s bite plates a metallic ball was fixed and the patient was submitted to lateral radiographic to obtain the lower facial height (LFHe) from cephalometric analysis. Additionally, from 40 lateral cephalograms of dentulous patients the LFHd was obtained. After that, the distance between metallic balls (DMB, in mm) was calculated to verify the linear difference when LFHe was changed to LFHd or LFHr, which provided the amount of wax to be added or removed from the bite plates, establishing a new method of OVD determination. LFHe, LFHd and LFHr values were submitted to t e z statistical tests and DMB differences were analyzed by Student’s t-test (α=0.05). Results: LFHr (47.0±4.0o a) was statistically higher than LFHd (44.9±5.6o b) and LFHe (43.5±3.5o b). There was statistical difference on linear discrepancies calculated between the LFHe and LFHd (1.7±4.1mm a) or LFHr (4.2±4.1mm b). Conclusion: The use of the cephalometric analysis showed to be a useful auxiliary tool in determining the intermaxillary relationship. However, this method must be associated with different clinical methods of OVD determination and it is recommended that regional references are used to calculate the linear discrepancies.

Todo o conteúdo deste livro está licenciado sob uma Licença de Atribuição Creative Commons. Atribuição 4.0 Internacional (CC BY 4.0). O conteúdo dos artigos e seus dados em sua forma, correção e confiabilidade são de responsabilidade exclusiva dos autores. Permitido o download da obra e o compartilhamento desde que sejam atribuídos créditos aos autores, mas sem a possibilidade de alterá-la de nenhuma forma ou utilizá-la para fins comerciais.