The influence of microstructure and surface roughness of the X5CrNi18-10 austenitic stainless steel-welded joint on resistance to uniform, pitting, and intergranular corrosion, as well as on the stability of the passive film, was evaluated. The microstructure was revealed by optical microscopy and scanning electron microscopy, whereas surface topography and roughness levels were determined by atomic force microscopy. Corrosion characteristics were obtained by the electrochemical potentiokinetic reactivation method with double loop, electrochemical impedance spectroscopy method, as well as by potentiodynamic measurements. The degree of sensitization of heat-affected zone (HAZ) was significantly lower than the threshold value required for the occurrence of intergranular corrosion. However, HAZ showed a significantly greater tendency to pitting and uniform corrosion compared to weld metal and base metal. No effect of roughness levels (RMS from 3.6 to 54 nm) on the pitting potential value of the welded joint was observed (unlike in HAZ). The polished surface shows significantly higher corrosion resistance than the grinded surface. Generally, polishing improved corrosion resistance, especially in HAZ, which is very important because HAZ is a critical place for the occurrence of pitting and other types of corrosion.

This study considers the corrosion behavior of the X5CrNi18 10 stainless steelwelded joint in NaCl solution, with and without the presence of several corrosion inhibitors (NaNO 3 , Ce(NO 3) 3 , and CeCl 3). The degree of sensitization of the welded joint to intergranular corrosion is determined using the electrochemical potentiokinetic reactivation method with a double-loop method. Pitting corrosion tests are performed by the potentiodynamic method. Resistance to general corrosion and the stability of the passive film is assessed based on the results of electrochemical impedance spectroscopy measurements, as well as on the values of the corrosion and passivation current. The main goal of this study is to determine the relation of the welded joint microstructure to general and pitting corrosion in the presence of the corrosion inhibitors. The value of pitting potential for the base metal and weld metal in the presence of the NaNO 3 or Ce(NO 3) 3 inhibitor is shifted to potentials in the transpassive area. The pitting potential for the heat-affected zone also possesses a noticeable higher value. However, nitrate ions do not increase the general corrosion resistance of any part of the welded joint. CeCl 3 does not increase resistance to general or pitting corrosion.

In this work, the essential oil of black pine (Pinus nigra J. F. Arnold) was used for the first time as a natural, ecological, and sustainable corrosion inhibitor for the acid cleaning of carbon steel. The essential oil was extracted by hydrodistillation using a Clevenger-type apparatus, and the oil was analyzed by gas chromatography–flame–ionization detection (GC–FID) and gas chromatography–mass spectrometry (GC–MS). The most abundant components in the essential oil were α-pinene, germacrene D, (E)-cariophyllene, and β-pinene. The inhibition efficiency was determined by electrochemical methods (electrochemical impedance spectroscopy and potentiodynamic polarization measurements). The results showed that the inhibitory efficiency of the black pine essential oil increases with time, reaching the highest values after 4 h of immersion for all inhibitor concentrations. It was also shown that black pine essential oil is a mixed-type inhibitor. The contact angle measurements confirmed that the black pine essential oil, as a new natural, environmentally safe inhibitor, is able to protect carbon steel from corrosion in a 1 M HCl solution.

The AISI 304 (X5CrNi19‐10) stainless steel is widely used for the production of various metal parts in power plants. A procedure for testing the influence of the dust from a power plant on resistance to general and pitting corrosion of the AISI 304 stainless steel is developed and performed. The quantitative (XRD method) and qualitative (Fourier–transform infrared spectroscopy [FTIR] method) composition of the dust present in the power plant is determined. Applying the Mott–Schottky method, the properties of the passive layer are analyzed, while a degree of chromium depletion of the grain boundary is determined by the electrochemical potentiokinetic reactivation method with double loop method. Values of polarization resistance (linear polarization resistance and electrochemical impedance spectroscopy methods) and the corrosion current density (polarization measurements) indicate that the stainless steel has a higher resistance to general corrosion in the dust solutions than in the etalon solution. Also, based on the measured value of the pitting potential (Epit) and the difference between the values of the pitting potential and the corrosion potential (Epit – Ecorr), it can be seen that stainless steel has a higher resistance to localized types of corrosion, such as pitting corrosion, in dust solutions than in the etalon solution.

This paper evaluated the inhibitory effect of Ce‐chloride and Na‐lactate mixture on the AA2024 aluminum alloy in 0.1 M NaCl solution. Electrochemical impedance spectroscopy (EIS) was applied for testing the general corrosion resistance, while potentiodynamic polarization measurement was applied for determining the alloy pitting corrosion resistance in NaCl and inhibitive solutions. The presence of cerium on the cathodic intermetallic particles was confirmed by scanning electron microscope/energy‐dispersive X‐ray spectroscopy analysis. The mixture of Ce‐chloride and Na‐lactate was a more effective corrosion inhibitor than Ce‐chloride alone. The inhibitors mixture is a mixed‐type corrosion inhibitor with a higher influence on slowing down the cathodic reaction of oxygen reduction. The adsorption of the inhibitor, the presence of cerium in different oxidation states (Ce3+ and Ce4+), and lactate anion (C–C/C–H, C–OH, C═O, and O–C═O group) were confirmed by X‐ray photoelectron spectroscopy analysis. A mechanism of inhibitor adsorption on the surface of AA2024 alloy in NaCl solution was proposed.