Super Duplex Stainless Steels (SDSSs) are composed of α-ferrite and γ-austenite grains, the simultaneous presence of which forms an optimal microstructure to achieve the best combination of mechanical and corrosion resistance properties. Moreover, international quality standards are strict about the phase fraction ratio. The purpose of this work is the achievement of a better description of the phase ratio evolution taking place during annealing at 1080 • C in the super duplex stainless steels F53-S32750 and F55-S32760. The experimental results show a damped sinusoidal trend in the α/γ phase ratio evolution with the increase of the soaking time of thermal treatment. This can be described by coupling both the competitive coarsening growth regime and the concept of the local equilibrium phase transformations, pointing out a good correspondence with the experimental data. Further, recrystallization phenomena also play a major role. Finally, the additivity character of the observed processes has been proven.
6xxx aluminum alloys are suitable for the realization of both structural applications and architectural decorative elements, thanks to the combination of high corrosion resistance and good surface finish. In areas where the aesthetic aspects are fundamental, further improvements in surface quality are significant. The cooling of the extrusion mold via internal liquid nitrogen fluxes is emerging as an important innovation in aluminum extrusion. Nowadays, this innovation is providing a large-scale solution to obtain high quality surface finishes in extruded aluminum semi-finished products. These results are also coupled to a significant increase in productivity. The aim of the work is to compare the surface quality of both cooled liquid nitrogen molds and classically extruded products. In this work, adhesion phenomena, occurring during the extrusion between the mold and the flowing material, have been detected as the main causes of the presence of surface defects. The analysis also highlighted a strong increase in the surface quality whenever the extrusion mold was cooled with liquid nitrogen fluxes. This improvement has further been confirmed by an analysis performed on the finished products, after painting and chromium plating. This work on the AA6060 alloy has moreover proceeded to roughness measurements and metallographic analyses, to investigate the eventual occurrence of other possible benefits stemming from this new extrusion mold cooling technology.
The integrated steelmaking cycle based on the blast furnace-basic oxygen furnace (BOF) route plays an important role in the production of plain and ultra-low carbon steel, especially for deep drawing operations. BOF steelmaking is based on the conversion of cast iron in steel by impinging oxygen on the metal bath at supersonic speed. In order to avoid the addition of detrimental chemical elements owing to the introduction of uncontrolled scrap and in order to decrease environmental impact caused by the intensive use of coke for the production of cast iron, HBI (hot briquetted iron) can be used as a source of metal and a fraction of cast iron. Forty industrial experimental tests were performed to evaluate the viability of the use of HBI in BOF. The experimental campaign was supported by a thermal prediction model and realized through the estimation of the oxidation enthalpy. Furthermore, the process was thermodynamically analyzed based on oxygen potentials using the off-gas composition and the bath temperature evolution during the conversion as reference data
Shot peening is a surface process commonly used in the aeronautic and automotive industries to improve fatigue resistance. Shot peening is proven to be beneficial in the fatigue behavior of components, but rarely has its influence on wear and pitting corrosion resistance been evaluated. In this work, shot peening was performed on AISI F55-UNS S32760 super-duplex stainless steel samples previously submitted to various thermal treatments, to obtain different initial microstructures and properties. Samples have been characterized in terms of microstructure morphology, local chemical composition, microhardness of each constituent phase, and energy dissipation modes. The enhanced properties provided by shot peening has been evaluated through residual stress depth profiles and Full Width at Half Maximum (FWHM) using X-ray diffraction (XRD), surface hardness, surface roughness, and corrosion resistance through salt spray fog tests. The 1400 °C solution thermal treatment was identified as the optimum initial condition, which maximizes the advantages of the shot peening treatment, even pitting corrosion resistance. These results are related to the uniformity of austenite and ferrite in terms of microstructure morphology, micromechanical properties, and alloying elements distribution.
Abstract:The behavior of super duplex stainless steels AISI F55-UNS S32760 in hot-dip aluminizing process has been studied, investigating the influence of cold working and of different initial microstructures obtained through a preliminary thermal treatment. The microstructural features examined are the secondary austenite precipitation, the static recovery of ferrite and the thermal dissolution of austenite within ferritic matrix. The hot-dip aluminizing temperature has been optimized through sessile drop tests. The treatment has been performed at 1100 • C for 300 s, 900 s and 2700 s. A strong chemical interaction occurs, generating intermetallic compounds at the interface. Molten aluminum interacts exclusively with the ferritic phase due to its much higher diffusivity in this phase coupled with its marked ferrite-stabilizer behavior. Thus, the influence of cold working is not remarkable, since the strains are mainly allocated by austenitic phase. The diffusivity of aluminum increases due to lattice defects thermally generated and, mainly, to influence given by grain boundaries, multiplied by secondary austenite precipitation, which act as short-circuit diffusion paths. Ni and Cr contents in the ferritic matrix have an influence but not highly relevant. Then, the best starting condition of the super duplex stainless steel substrates, to obtain a thick interfacial layer, are the thermal annealing at 1080 • C for 360 s/mm after a solution thermal treatment at 1300 • C for 60 s/mm.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.