Data on treatment of glucocorticoid-induced osteoporosis (GIO) in men are scarce. We performed a randomized, open-label trial in men who have taken glucocorticoids (GC) for ≥3 months, and had an areal bone mineral density (aBMD) T-score ≤ –1.5 standard deviations. Subjects received 20 μg/d teriparatide (n = 45) or 35 mg/week risedronate (n = 47) for 18 months. Primary objective was to compare lumbar spine (L1–L3) BMD measured by quantitative computed tomography (QCT). Secondary outcomes included BMD and microstructure measured by high-resolution QCT (HRQCT) at the 12th thoracic vertebra, biomechanical effects for axial compression, anterior bending, and axial torsion evaluated by finite element (FE) analysis from HRQCT data, aBMD by dual X-ray absorptiometry, biochemical markers, and safety. Computed tomography scans were performed at 0, 6, and 18 months. A mixed model repeated measures analysis was performed to compare changes from baseline between groups. Mean age was 56.3 years. Median GC dose and duration were 8.8 mg/d and 6.4 years, respectively; 39.1% of subjects had a prevalent fracture, and 32.6% received prior bisphosphonate treatment. At 18 months, trabecular BMD had significantly increased for both treatments, with significantly greater increases with teriparatide (16.3% versus 3.8%; p = 0.004). HRQCT trabecular and cortical variables significantly increased for both treatments with significantly larger improvements for teriparatide for integral and trabecular BMD and bone surface to volume ratio (BS/BV) as a microstructural measure. Vertebral strength increases at 18 months were significant in both groups (teriparatide: 26.0% to 34.0%; risedronate: 4.2% to 6.7%), with significantly higher increases in the teriparatide group for all loading modes (0.005 < p < 0.015). Adverse events were similar between groups. None of the patients on teriparatide but five (10.6%) on risedronate developed new clinical fractures (p = 0.056). In conclusion, in this 18-month trial in men with GIO, teriparatide showed larger improvements in spinal BMD, microstructure, and FE-derived strength than risedronate.

No abstract

The key parameters determining the elastic properties of an unidirectional mineralized bone fibril-array decomposed in two further hierarchical levels are investigated using mean field methods. Modeling of the elastic properties of mineralized micro- and nanostructures requires accurate information about the underlying topology and the constituents' material properties. These input data are still afflicted by great uncertainties and their influence on computed elastic constants of a bone fibril-array remains unclear. In this work, mean field methods are applied to model mineralized fibrils, the extra-fibrillar matrix and the resulting fibril-array. The isotropic or transverse isotropic elastic constants of these constituents are computed as a function of degree of mineralization, mineral distribution between fibrils and extra-fibrillar matrix, collagen stiffness and fibril volume fraction. The linear sensitivity of the elastic constants was assessed at a default set of the above parameters. The strain ratios between the constituents as well as the axial and transverse indentation moduli of the fibril-array were calculated for comparison with experiments. Results indicate that the degree of mineralization and the collagen stiffness dominate fibril-array elasticity. Interestingly, the stiffness of the extra-fibrillar matrix has a strong influence on transverse and shear moduli of the fibril-array. The axial strain of the intra-fibrillar mineral platelets is 30-90% of the applied fibril strain, depending on mineralization and collagen stiffness. The fibril-to-fibril-array strain ratio is essentially ~1. This study provides an improved insight in the parameters, which govern the fibril-array stiffness of mineralized tissues such as bone.

In this study, the homogenized anisotropic elastic properties of single bone lamellae are computed using a finite element unit cell method. The resulting stiffness tensor is utilized to calculate indentation moduli for multiple indentation directions in the lamella plane which are then related to nanoindentation experiments. The model accounts for different fibril orientation patterns in the lamellae--the twisted and orthogonal plywood pattern, a 5-sublayer pattern and an X-ray diffraction-based pattern. Three-dimensional sectional views of each pattern facilitate the comparison to transmission electron (TEM) images of real lamella cuts. The model results indicate, that the 5-sublayer- and the X-ray diffraction-based patterns cause the lamellae to have a stiffness maximum between 0° and 45° to the osteon axis. Their in-plane stiffness characteristics are qualitatively matching the experimental findings that report a higher stiffness in the osteon axis than in the circumferential direction. In contrast, lamellae owning the orthogonal or twisted plywood fibril orientation patterns have no preferred stiffness alignment. This work shows that the variety of fibril orientation patterns leads to qualitative and quantitative differences in the lamella elastic mechanical behavior. The study is a step toward a deeper understanding of the structure-mechanical function relationship of bone lamellae.

Haversian systems or ‘osteons’ are cylindrical structures, formed by bone lamellae, that make up the major part of human cortical bone. Despite their discovery centuries ago in 1691 by Clopton Havers, their mechanical properties are still poorly understood.The objective of this study is a detailed identification of the anisotropic elastic properties of the secondary osteon in the lamella plane. Additionally, the principal material orientation with respect to the osteon is assessed. Therefore a new nanoindentation method was developed which allows the measurement of indentation data in three distinct planes on a single osteon.All investigated osteons appeared to be anisotropic with a preferred stiffness alignment along the axial direction with a small average helical winding around the osteon axis. The mean degree of anisotropy was 1.75 ± 0.36 and the mean helix angle was 10.3°±0.8°.These findings oppose two well established views of compact bone microstructure: first, the generally clear axial stiffness orientation contradicts a regular ‘twisted plywood’ collagen fibril orientation pattern in lamellar bone that would lead to a more isotropic behavior. Second, the class of transverse osteons were not observed from the mechanical point of view.