No abstract

No abstract

The amount of different persistent organic pollutants (POPs) in the input of waste incinerators was compared to that in the output. Three cases were considered: a rotary kiln incinerating hazardous waste, a grate furnace incinerating municipal solid waste (MSW) and the same grate furnace co-incinerating plastics of waste of electrical and electronic equipment (WEEE) and automotive shredder residue (ASR) with MSW. The mass balance for PCBs in the rotary kiln indicates that these POPs are destroyed effectively during incineration. The grate furnace can be a sink or source of PCDD/Fs and PCBs depending on the concentrations in the incinerated waste. In order to compare the total amount of POPs in input and output, a methodology was developed whereby the amount of POPs was weighed according to minimal risk doses (MRDs) or cancer potency factors. For both incinerators the PCDD/Fs, PCBs and polyaromatic hydrocarbons (PAHs) are the main contributors to total weighed POP output. In MSW, the PCDD/Fs, PBDD/Fs and polybrominated diphenylethers (PBDEs) are the main contributors to the weighed POP input. The ratios of the weighed POP-input over -output clearly indicate that the rotary kiln incinerating hazardous waste is a weighed POP sink. The grate furnace incinerating MSW is a weighed POP sink or source depending on the POP-concentrations in the waste, but the difference between output and input is rather limited. When e.g. ASR and plastics of WEEE, containing high concentrations of PBDEs and PCBs, are co-incinerated in the grate furnace, it is clearly a weighed POP sink.

The European directive 2000/53/EC implies a "reuse and recovery" rate for end-of-life vehicles (ELVs) of 95% to be reached by the year 2015. One of the options to increase the actual average European "reuse and recovery" rate of approximately 78% (EU 15, 2008) is incineration of automotive shredder residue (ASR) with energy-recovery. The mass balance and the congener fingerprints for PCDD/Fs, dioxin-like PCBs, PCBs and PAHs in a real scale fluidized bed combustor (FBC) incinerating 25% ASR with 25% refuse derived fuel (RDF) and 50% waste water treatment sludge (WWT sludge) were investigated. The PCDD/F, dioxin-like PCB, PCB and PAH concentrations in this input waste mix were more than hundred times higher than in the usual waste feed of the incinerator (30% RFD and 70% WWT sludge). In the outputs of the FBC, however, the concentrations of these POP groups were comparable or only slightly higher than in the outputs generated during the incineration of the usual waste feed. The considered POPs in the waste were destroyed efficiently and the formation of new POPs during cooling of the flue gas appeared to a large extent independent of the POP concentrations in the incinerated waste.

In the incubation process of domestic avian eggs, the development of the embryo is mainly influenced by the physical microenvironment around the egg. Only small spatiotemporal deviations in the optimal incubator air temperature are allowed to optimize hatchability and hatchling quality. The temperature of the embryo depends on 3 factors: (1) the air temperature, (2) the exchange of heat between the egg and its microenvironment and (3) the time-variable heat production of the embryo. Theoretical estimates on the heat exchange between an egg and its physical microenvironment are approximated using equations that assume an approximate spherical shape for eggs. The objective of this research was to determine the heat transfer between the eggshell and its microenvironment and then compare this value to various theoretical estimates. By using experimental data, the overall and the convective heat transfer coefficients were determined as a function of heat production, air humidity, air speed, and air temperature. Heat transfer was not affected by air humidity but solely by air temperature, embryonic heat generation, and air speed and flow around eggs. Also, heat transfer in forced-air incubators occurs mainly by convective heat loss, which is dependent on the speed of airflow. A vertical airflow is more efficient than a horizontal airflow in transferring heat from the egg. We showed that describing an egg as a sphere underestimated convective heat transfer by 33% and was, therefore, too simplistic to accurately assess actual heat transfer from real eggs.