This contribution is focused on the influence of build orientation on hardness of materials sintered using direct metal laser sintering (DMLS) technology. It builds on the current research works that has monitored the influence of build orientation on a fatigue life, mechanical properties, roughness after machining, etc. In the mentioned work, a slight influence of build orientation on the above properties was shown. The hardness was measured on a Ti6Al4V alloy which was made of powder by DMLS technology. The individual materials were sintered at different laser powers, then annealed to remove internal stresses. Part of the experiment examined the metallographic analysis of materials in the direction perpendicular to the sintered layers and parallel with the sintered layers. Microhardness was measured on metallographic cross-sections and the results were statistically processed. The influence of laser power on a respective material hardness was assessed by one-way analysis of variance (ANOVA), a comparison of the hardness between sintered and sintered-annealed samples, as well as the comparison of hardness in the two considered directions was performed by t-test and F-test. A statistically significant difference in the hardness of the materials prepared at different laser powers was found. The influence of heat treatment, as well as the direction of material building also showed a statistically significant difference.

This article deals with the evaluation of material wear of injection molds made of aluminium alloy Alumec 89 and copper alloy Moldmax HH in friction couples with polymer materials with various filler contents. The friction relations in injection molding were simulated in an adhesion dry wear test using an Amsler machine, with an area contact of the friction couple materials. The wear intensity was evaluated by determination of friction coefficient and relative wearing by the mass loss. Surface morphology changes of evaluated alloys after wear and the thermal conditions in particular friction couples were analyzed simultaneously.

Ti6Al4V samples have been prepared by Direct Metal Laser Sintering (DMLS) with varied laser power. Some of the samples were stress-relief annealed. The microstructure of materials was investigated using a light microscopy. Columnar grains of martensite dominate in as-made microstructure. Stress-relief annealing led to the white acicular phase growth in the structure with a fishbone arrangement on the boundary of some original martensitic needles. Mechanical properties of materials were characterized through hardness measurement in two directions relating to the sample building direction. It was found that the hardness of materials increased with a laser power and values varied from 370 to 415 HV 0.3/30. After stress-relief annealing, the structure of materials being homogenized, pattern spacing dissolved and the hardness in both directions became stabilized at values of 350-370 HV 0.3/30. The laser power affects the corrosion rate of the material. The lowest corrosion rate was recorded at the maximum laser power (190 W). Heat treatment does not affect the corrosion rate remarkably, however it leads to stabilization of corrosion potential of materials Ecorr. The surface of the samples was modified by an abrasive blasting using spherical (zirblast) and sharp-edged (white corundum) blasting abrasives and three levels of air pressure. The abrasive blasting of sintered materials led to a decrease of the surface roughness of materials with air pressure increasing. Blasting with zirblast led to a more significant decrease of roughness parameters compared with surfaces blasted with sharp-edged white aluminum. Different shapes of abrasives caused characteristic surface morphology.

No abstract

The paper is focused on investigating the quality of two grades of thermally sprayed coatings deposited by high-velocity oxygen fuel (HVOF) technology. One grade contains WC hard particles in an environmentally progressive Ni-and Co-free FeCrAl matrix, while the second coating contains WC and WB hard particles in a cobalt matrix. The aim of the experimental work was to determine the effect of thermal cyclic loading on the coatings' resistance to adhesive, abrasive and erosive wear. Abrasive wear was evaluated using abrasive cloth of two grit sizes, and erosive wear was evaluated by a dry-pot wear test in a pin mill at two sample angles. Adhesion wear resistance of the coatings was determined by a sliding wear test under dry friction conditions and in a 1 mol water solution of NaCl. Corrosion resistance of the coatings was evaluated using potentiodynamic polarization tests. Metallographic cross-sections were used for measurement of the microhardness and thickness and for line energy-dispersive X-ray (EDX) analysis. The tests proved the excellent resistance of both coatings against adhesive, abrasive, and erosive wear, as well as the ability of the WC-WB-Co coating to withstand alternating temperatures of up to 600 • C. The "green carbide" coating (WC-FeCrAl) can be recommended as an environmentally friendly replacement for Ni-and Co-containing coatings, but its operating temperature is strictly limited to 500 • C in air.