This report is available at no cost from the National Renewable Energy Laboratory (NREL) at www.nrel.gov/publications. U.S. Department of Energy (DOE) reports produced after 1991 and a growing number of pre-1991 documents are available free via www.OSTI.gov.NREL prints on paper that contains recycled content.

Scale-model wave basin testing is often employed in the development and validation oflarge-scale offshore vessels and structures by the oil and gas, military, and marine industries. A basin-model test requires less time, resources, and risk than a full-scale test, while providing real and accurate data for numerical simulator validation. As the development of floating wind turbine technology progresses in order to capture the vast deepwater wind energy resource, it is clear that model testing will be essential for the economical and efficient advancement of this technology. However, the scale model testing of floating wind turbines requires accurate simulation of the wind and wave environments, structural flexibility, and wind turbine aerodynamics and thus requires a comprehensive scaling methodology. This paper presents a unified methodology for Froude scale model testing of floating wind turbines under combined wind and wave loading. First, an overview of the scaling relationships employed for the environment, floater, and wind turbine are presented. Aftemwd, a discussion is presented concerning suggested methods for manufacturing a high-quality, low-turbulence Froude scale wind environment in a wave basin to facilitate simultaneous application of wind and waves to the model. Subsequently, the difficulties of scaling the highly Reynolds number-dependent wind turbine aerodynamics is presented in addition to methods for tailoring the turbine and wind characteristics to best emulate the full-scale condition. Lastly, the scaling methodology is demonstrated using results from 1150th-scale floating wind turbine testing performed at the Maritime Research Institute Netherlands (MARIN) Offshore Basin. The model test campaign investigated the response of the 126 -m rotor diameter National Renewable Energy Lab (NREL) horizontal axis wind turbine atop three floating platforms: a tension-leg platform, a spar-buoy, and a semisubmersible. The results highlight the methodology's strengths and weaknesses for simulating full-scale global response of floating wind turbine systems.In order to establish a scaling methodology, a particular set of rules and constraints must be selected. The suggested scaling Journal of Offshore Mechanics and Arctic Engineering

a b s t r a c tDesign parameters needed for the development of Maine's offshore wind resource are calculated using Gulf of Maine buoy data. Extreme values of the significant wave height and mean associated peak period, eight minute average wind speed, and five second average gust wind speed are estimated using a Peaks Over Threshold (POT) extreme value estimation technique. Wind shear coefficients and gust factors are also estimated. Seven to thirty-two years of buoy data at five locations near areas of possible interest to Maine's offshore wind industry were examined. Buoy data was obtained from the University of Maine and the National Oceanic Atmospheric Administration. Predictions of extreme significant wave heights in this study compare well with past shipboard and hindcast predictions for open water sites. Sites closer to shore show larger differences from past predictions due to the large areal scale of the earlier studies. Extreme wind speeds and shear coefficients compare well with coastal onshore wind speeds published

Scale model wave basin testing is often employed in the development and validation of large scale offshore vessels and structures by the oil and gas, military and marine industries. A basin model test requires less time, resources and risk than a full scale test while providing real and accurate data for model validation. As the development of floating wind turbine technology progresses in order to capture the vast deepwater wind energy resource, it is clear that model testing will be essential for the economical and efficient advancement of this technology. However, the scale model testing of floating wind turbines requires one to accurately simulate the wind and wave environments, structural flexibility and wind turbine aerodynamics, and thus requires a comprehensive scaling methodology. This paper presents a unified methodology for Froude scale testing of floating wind turbines under combined wind and wave loading. First, an overview of the scaling relationships employed for the environment, floater and wind turbine are presented. Afterward, a discussion is presented concerning suggested methods for manufacturing a high-quality, low turbulence Froude scale wind environment in a wave basin to facilitate simultaneous application of wind and waves to the model. Subsequently, the difficulties of scaling the highly Reynolds number-dependent wind turbine aerodynamics is presented in addition to methods for tailoring the turbine and wind characteristics to best emulate the full scale condition. Lastly, the scaling methodology is demonstrated using results from 1/50th scale floating wind turbine testing performed at MARIN’s (Maritime Research Institute Netherlands) Offshore Basin which tested the 126 m rotor diameter NREL (National Renewable Energy Lab) horizontal axis wind turbine atop three floating platforms: a tension-leg platform, a spar-buoy and a semi-submersible. The results demonstrate the methodology’s ability to adequately simulate full scale global response of floating wind turbine systems.

A new floating wind turbine platform design called VolturnUS developed by the University of Maine uses innovations in materials, construction, and deployment technologies such as a concrete semi-submersible hull and a composite tower to reduce the costs of offshore wind. These novel characteristics require research and development prior to full-scale construction. This paper presents a unique offshore model testing effort aimed at de-risking full-scale commercial projects by providing properly scaled global motion data, allowing for implementation of full-scale structural materials, and demonstrating full-scale construction and deployment methods. The model is a 1:8-scale model of a 6MW semi-submersible floating wind turbine and was deployed offshore Castine, Maine, USA in June, 2013. The model uses a fully operational turbine and was the first grid connected offshore wind turbine in the Americas. The testing effort includes careful treatment of the offshore test site, scaling methods, model design, and construction. A suitable test site was identified that provides the correct proportions of wind and wave loading in order to simulate design load cases prescribed by the American Bureau of Shipping Standard for Building and Classing Floating Offshore Wind Turbines. Sample model test data is provided. Model test data is directly compared to full-scale design predictions made using coupled aeroelastic/ hydrodynamic software. VolturnUS performance data from scaled extreme sea states show excellent agreement with predictive models. Model test data are also compared to a numerical representation of the physical model for the purposes of numerical code validation. The numerical model results compare very favorably with data collected from the physical model.