During last few decades, membrane technology has emerged as an efficient technique over conventional methods due to its high removal capacity, ease in operation and cost effectiveness for wastewater treatment and production of clean water. Membrane based separations are commonly based on polymeric membranes because of their higher flexibility, easily pore forming mechanism, low cost and smaller space for installation as compared to inorganic membranes. Commonly employed membrane fabrication phase inversion method has been shortly reviewed in this article. Major limitation of membrane based separations is fouling and polymeric membranes being hydrophobic in nature are more prone to fouling. Fouling is a deposition of various colloidal particles, macromolecules (polysaccharides, proteins), salts etc. on membrane surface and within pores thus impedes membrane performance, reduces flux and results in high cost. Modification of polymeric membranes due to its tailoring ability with nanomaterials such as metal based and carbon based results in polymeric nano-composite membranes with high antifouling characteristics. Nanomaterials impart high selectivity, permeability, hydrophilicity, thermal stability, mechanical strength, and antibacterial properties to polymeric membranes via blending, coating etc. modification methods. Characterization techniques has also discussed in later section for studying morphological properties and performance of polymer nano-composite membranes. Graphical Abstract

A novel, functionalized graphene oxide–based cellulose acetate membrane was fabricated using the phase inversion method to improve the membrane characteristics and performance. We studied the effect of aminated graphene oxide (NH2–GO) composite on the CA membrane characteristics and performance in terms of membrane chemistry, hydrophilicity, thermal and mechanical stability, permeation flux, and antibacterial activity. The results of contact angle and water flux indicate the improved hydrophilic behavior of composite membranes in comparison to that of the pure CA membrane. The AGO-3 membrane showed the highest water flux of about 153 Lm−2h−1. The addition of hydrophilic AGO additive in CA membranes enhanced the antibacterial activity of AGO–CA membranes, and the thermal stability of the resulting membrane also improved since it increases the Tg value in comparison to that of a pristine CA membrane. The aminated graphene oxide (NH2–GO) was, therefore, found to be a promising additive for the fabrication of composite membranes with potent applications in wastewater treatment.

In this study, cellulose acetate (CA) was blended with sulfonated graphene oxide (SGO) nanomaterials to endow a nanocomposite membrane for wastewater treatment with improved hydrophilicity and anti-biofouling behavior. The phase inversion method was employed for membrane fabrication using tetrahydrofuran (THF) as the solvent. The characteristics of CA-SGO-doped membranes were investigated through thermal analysis, contact angle, SEM, FTIR, and anti-biofouling property. Results indicated that anti-biofouling property and hydrophilicity of CA-SGO nanocomposite membranes were enhanced with addition of hydrophilic SGO nanomaterials in comparison to pristine CA membrane. FTIR analysis confirmed the successful decoration of SGO groups on CA membrane surface while revealing its morphological properties through SEM analysis. Thermal analysis performed using DSC confirmed the increase in thermal stability of CA-SGO membranes with addition of SGO content than pure CA membrane.

Emergence of membrane technology for effective performance is qualified due to its low energy consumption, no use of chemicals, high removal capacity and easy accessibility of membrane material. The hydrophobic nature of polymeric membranes limits their applications due to biofouling (assemblage of microorganisms on surface of membrane). Polymeric nanocomposite membranes emerge to alleviate this issue. The current research work was concerned with the fabrication of sulfonated graphene oxide doped polyvinylidene fluoride (PVDF) membrane and investigation of its anti-biofouling and anti-bacterial behavior. The membrane was fabricated through phase inversion method, and its structure and morphology were characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-rays diffraction (XRD) and thermo gravimetric analysis (TGA) techniques. Performance of the membrane was evaluated via pure water flux; anti-biofouling behavior was determined through Bovine Serum albumin (BSA) rejection. Our results revealed that the highest water flux was shown by M7 membrane about 308.7 Lm−2h−1/bar having (0.5%) concentration of SGO with improved BSA rejection. Furthermore, these fabricated membranes showed high antibacterial activity, more hydrophilicity and mechanical strength as compared to pristine PVDF membranes. It was concluded that SGO addition within PVDF polymer matrix enhanced the properties and performance of membranes. Therefore, SGO was found to be a promising material for the fabrication of nanocomposite membranes.

Water scarcity has become one of the most significant problems globally. Membrane technology has gained considerable attention in water treatment technologies. Polymeric nanocomposite membranes are based on several properties, with enhanced water flux, high hydrophilicity and anti-biofouling behavior, improving the membrane performance, flexibility, cost-effectiveness and excellent separation properties. In this study, aminated graphene oxide (NH2-GO)-based PVDF membranes were fabricated using a phase-inversion method for textile dye removal. These fabricated membranes showed the highest water flux at about 170.2 (J/L.h−1.m−2) and 98.2% BSA rejection. Moreover, these membranes removed about 96.6% and 88.5% of methylene blue and methyl orange, respectively. Aminated graphene oxide-based polyvinylidene fluoride (PVDF) membranes emerge as a good membrane material that enhances the membrane performance.