No abstract

No abstract

Monitoring of human motor and muscle activity is used in many areas, from prosthetics during rehabilitation to training monitoring of athletes. Sensors for these tasks are usually made of flexible polymers and require recycling after the expiration date. Nanocellulose (NC) can be used as a biodegradable base for this type of sensor. The development of low-cost disposable sensors that do not require disinfection and cleaning is relevant. NC is a composite nanoscale structure of cellulose fibers (fibrils) with a high aspect ratio. The paper aim is to develop disposable wearable biodegradable bend sensors based on nanocellulose using vacuum synthesis methods and the study of their characteristics. Nanocellulose was synthesized by the TEMPO method. The sensors were created by means of magnetron sputtering of Ti/Ni or Cr/Ni thin films at the surface of nanocellulose. Measuring stand was developed to determine the change in resistance due to the bending of the sensor. It’s mechanical part consists of an elastic deformation plate made of high-alloy steel, which can be bent using a micrometric screw. The change in resistance is linearly related to the elongation of the measured sample. A Wheatstone bridge and a 24-Bit ADC HX711 were used to measure the change in resistance. During testing of the sensor for analysis of muscle activity, the sensor element was attached to the human skin with the help of medical glue BF-6. The obtained sensors were tested for biodegradability. The samples were placed in the ground at a depth of 20-30 mm. The mass of nanocellulose samples was measured using a high-precision digital balance EDIS 50 (50/0.001 g) with a built-in level. The optimal ratio of the value of sensitivity and reversibility is observed in the range of the nominal resistance of the nickel film from 10 to 100 Ohms. This is due to an increase in the surface area of ​​the Ni film, which leads to an increase in sensitivity, but at the same time there is a decrease in the repeatability of the characteristics due to a greater influence of the heterogeneous structure of nanofibrillated cellulose. In addition, sensors with different buffer layer materials - Ti and Cr - were selected for testing. For titanium-based sensors, the maximum sensitivity coefficient is 0.312%, while the deviation of the sensor signal after one bending-unfolding cycle (reversibility) is less than 0.001%. Chromium-based sensors have significantly higher sensitivity (0.9753%), but worse reversibility (7.14%). Sensors based on the Cr buffer layer showed poorly reproducible results in the cyclic mode of operation, namely: there are significant fluctuations in the signal amplitude (up to 50-60%) already after the second bending-unfolding cycle. Therefore, despite the high sensitivity of such sensors, they are unsuitable for analyzing human motor and muscle activity/ The sensors based on the Ti buffer layer showed good response (2.5-3%) and good repeatability and resistance to cyclic bending (30 times). It can be seen that the obtained dependencies are approximated by a linear law. Some deviation from linearity is obviously related to the inhomogeneity of the Ni thin film. Also, the sensors showed a good loss of mass (40% in 9 weeks) during the biodegradability test, which confirms their ability to decompose under the influence of atmospheric phenomena. So, in this work, disposable wearable sensors on a nanocellulose substrate were synthesized for the evaluation of motor and muscle activity of a person. It was found that such sensors can be used to test of finger and biceps movement during at least 10-30 full flexion-extension cycles. For test of elbow movement, it is planned to synthesize a high-elastic composite material based on nanocellulose and bioelastic material (for example, polyvinyl alcohol). Thus, the proposed sensor manufacturing technology makes it possible to obtain cheap, light, flexible disposable wearable sensors that do not require further disposal after the end of operation.

Problems. Rapid technical progress has led to a reduction in the useful life of consumer electronics. The introduction of green, flexible, biodegradable electronic devices will prevent an environmental catastrophe. Recently, the use of organic materials instead of inorganic analogues has become increasingly popular, which makes it possible to move from rigid solid-state sensors for multiple use that require disposal to flexible, disposable sensors that are suitable for human wear on the body or clothing and for spontaneous decomposition in nature after using. One of such promising organic materials is nanocellulose. The aim of the study. Studying the possibility of nanocellulose application for the manufacture of flexible, wearable, disposable sensors of various types of physical and chemical quantities. Methodology of implementation. In the article the analysis, classification and comparision of various technologies and features of synthesis, as well as the main characteristics of flexible sensors made on the basis of nanocellulose were fulfilled. Also the main parameters of flexible sensors based on nanocellulose were being compared with corresponding analogs of sensors based on artificial polymers. Research results. The paper established the physical and technological features of using nanocellulose for the manufacture of sensors of various types of physical and chemical quantities in order to improve their performance. It has been established that nanocellulose can be used both as a substrate and as a sensitive element of a sensor. It has also been shown that nanocellulose is suitable for use in sensors based on both electrical physical phenomena and optical effects. Conclusions. Nanocellulose is a promising biodegradable material on the basis of which flexible, disposable, wearable sensors can be created. The manufacturing technology of such sensors should contain only low-temperature and dry processing processes. For effective use in certain types of sensors, it is advisable to manufacture nanocellulose with a modified surface or in the form of composites with other nanomaterials. Based on the obtained results, it is possible to improve existing and develop new methods of creating flexible wearable disposable sensors that do not require disposal.