We evaluated the effectiveness of 2-phenylethanol (PET) in combination with acetic acid (AA) as a binary lure for monitoring male and female obliquebanded leafroller, Choristoneura rosaceana (Harris). Studies were conducted in apple, Malus domestica Borkhausen, orchards treated with or without sex pheromone dispensers for mating disruption (MD). Open polypropylene vials, closed membrane cups, and rubber septa loaded with AA and/or PET in varying amounts were first evaluated in a series of trapping experiments. Membrane cups loaded with 800 mg of PET were as effective as 10-mg septa, but longer lasting, and were comparable to the open vials. A membrane cup AA lure was effective in tests, but further work is needed to increase its release rate and extend its activity. Catches of codling moth, Cydia pomonella (L.), and C. rosaceana were unaffected by combining PET with (E,E)-8,10-dodecadien-1-ol, the sex pheromone of codling moth, pear ester, (E,Z)-2,4-ethyl-decadienoate, and AA lures. Adding (E)-4,8-dimethyl-1,3,7-nonatriene to this blend to enhance codling moth catch, significantly reduced catches of C. rosaceana. PET+AA was a more attractive binary lure than AA plus phenylacetonitrile (PAN) for C. rosaceana. The addition of PET or PAN to traps already baited with the sex pheromone of C. rosaceana significantly reduced male catches. Traps baited with PET+AA placed in blocks not treated with MD caught significantly fewer C. rosaceana than traps baited with sex pheromone. In comparison, sex pheromone-baited traps in MD blocks caught ≤ 1 male moth per season which was significantly lower than total moth (> 10) or female moth (≥ 3) catch in these blocks with PET+AA. A high proportion (> 70%) of trapped females were mated in both untreated and MD-treated orchards. Further refinement of this binary, bisexual lure using membrane cup technology may allow the establishment of action thresholds and improve management timings for C. rosaceana.

No abstract

While drilling an 8.5 in. open hole in the Umm Shaif field, an unexpected fault was encountered across formation ARAB-D2, increasing losses from 15.0 to 40.0 bbl/hr. Initial losses were managed using mud lost-circulation material (LCM) pills; however, losses were observed again while running the liner. It was decided to cement the liner to secure the shoe, with the expectation of being required to perform a remedial operation. The liner was cemented with all precautions to help prevent further loss. By systematically introducing enhancements to the cementing and liner running practices and optimizing the fluid (cement/spacer) design using the latest technology fiber system in the spacer, it was possible to achieve the objective to control losses during the cementing operation. Additionally, securing the shoe and isolating the reservoir zone while preparing for a top-of-liner squeeze and liner perforation, if necessary, to squeeze cement in poorly isolated zones was achieved. Three-dimensional (3D) placement simulator software was used to model the flow rates and the equivalent circulating density (ECD) during the operation, and sensitivity runs were performed to observe worst-case scenarios at different loss rates to optimize volumes, rates, etc. Once the spacer crossed the loss zone, lost-circulation additives (composed of a blend of various additives) began bridging across the zone, enabling the cement slurry to reach the top of liner, where it circulated excess cement. The tagged hard cement above the top-of-liner log exhibited good isolation to the reservoir formation, no remedial operations were necessary for the shoe and top of liner, and no perforations were necessary. Spacer fluids are an environmentally acceptable blend of carefully selected materials, including coarse and tough LCM, fibers, and medium-sized, resilient angular materials. These fluid systems help mitigate losses when cementing across weak, unconsolidated, or fractured formations and carry materials with both high-pressure integrity and compressibility to help ensure tolerance to modifications in fracture size, caused by differential pressure fluctuations, without the materials being dislodged or allowing collapse. These materials are stable and insoluble in water. The spacer fluid system breaks the emulsion of oil-based drilling fluid, water wetting the casing pipe and the formation in preparation for cement bonding. Additionally, such materials resist intermingling of fluids at the interface in the fluid train.