BackgroundIn converting biomass to bioethanol, pretreatment is a key step intended to render cellulose more amenable and accessible to cellulase enzymes and thus increase glucose yields. In this study, four cellulose samples with different degrees of polymerization and crystallinity indexes were subjected to aqueous sodium hydroxide and anhydrous liquid ammonia treatments. The effects of the treatments on cellulose crystalline structure were studied, in addition to the effects on the digestibility of the celluloses by a cellulase complex.ResultsFrom X-ray diffractograms and nuclear magnetic resonance spectra, it was revealed that treatment with liquid ammonia produced the cellulose IIII allomorph; however, crystallinity depended on treatment conditions. Treatment at a low temperature (25°C) resulted in a less crystalline product, whereas treatment at elevated temperatures (130°C or 140°C) gave a more crystalline product. Treatment of cellulose I with aqueous sodium hydroxide (16.5 percent by weight) resulted in formation of cellulose II, but also produced a much less crystalline cellulose. The relative digestibilities of the different cellulose allomorphs were tested by exposing the treated and untreated cellulose samples to a commercial enzyme mixture (Genencor-Danisco; GC 220). The digestibility results showed that the starting cellulose I samples were the least digestible (except for corn stover cellulose, which had a high amorphous content). Treatment with sodium hydroxide produced the most digestible cellulose, followed by treatment with liquid ammonia at a low temperature. Factor analysis indicated that initial rates of digestion (up to 24 hours) were most strongly correlated with amorphous content. Correlation of allomorph type with digestibility was weak, but was strongest with cellulose conversion at later times. The cellulose IIII samples produced at higher temperatures had comparable crystallinities to the initial cellulose I samples, but achieved higher levels of cellulose conversion, at longer digestion times.ConclusionsEarlier studies have focused on determining which cellulose allomorph is the most digestible. In this study we have found that the chemical treatments to produce different allomorphs also changed the crystallinity of the cellulose, and this had a significant effect on the digestibility of the substrate. When determining the relative digestibilities of different cellulose allomorphs it is essential to also consider the relative crystallinities of the celluloses being tested.

Lignocellulosic biorefineries will produce a substantial pool of lignin-enriched residues, which are currently slated to be burned for heat and power. Going forward, however, valorization strategies for residual solid lignin will be essential to the economic viability of modern biorefineries. To achieve these strategies, effective lignin depolymerization processes will be required that can convert specific lignin-enriched biorefinery substrates into products of sufficient value and market size. Base-catalyzed depolymerization (BCD) of lignin using sodium hydroxide and other basic media has been shown to be an effective depolymerization approach when using technical and isolated lignins relevant to the pulp and paper industry. To gain insights in the application of BCD to lignin-rich, biofuels-relevant residues, here we apply BCD with sodium hydroxide at two catalyst loadings and temperatures of 270, 300, and 330 °C for 40 min to residual biomass from typical and emerging biochemical conversion processes. We obtained mass balances for each fraction from BCD, and characterized the resulting aqueous and solid residues using gel permeation chromatography, NMR, and GC–MS. When taken together, these results indicate that a significant fraction (45–78%) of the starting lignin-rich material can be depolymerized to low molecular weight, water-soluble species. The yield of the aqueous soluble fraction depends significantly on biomass processing method used prior to BCD. Namely, dilute acid pretreatment results in lower water-soluble yields compared to biomass processing that involves no acid pretreatment. Also, we find that the BCD product selectivity can be tuned with temperature to give higher yields of methoxyphenols at lower temperature, and a higher relative content of benzenediols with a greater extent of alkylation on the aromatic rings at higher temperature. Overall, this study shows that residual, lignin-rich biomass produced from conventional and emerging biochemical conversion processes can be depolymerized with sodium hydroxide to produce significant yields of low molecular weight aromatics that potentially can be upgraded to fuels or chemicals.

Biomass pretreatment generally aims to increase accessibility to plant cell wall polysaccharides for carbohydrate-active enzymes to produce sugars for biological or catalytic upgrading to ethanol or advanced biofuels. Significant research has been conducted on a suite of pretreatment processes for bioethanol processes. An alternative option, which has received less attention in the biofuels community, is the use of alkaline pretreatment for the partial depolymerization of lignin from intact biomass. A known issue with alkaline pretreatment is the loss of polysaccharides from peeling reactions, but this loss can be mitigated with anthraquinone, as commonly practiced in pulping. Here, we conduct a comprehensive bench-scale evaluation of alkaline pretreatment using corn stover at temperatures of 100, 130, and 160 °C and sodium hydroxide loadings from 35 to 660 mg NaOH/g dry biomass with anthraquinone. Compositional analysis is conducted on the starting material and residual solids after pretreatment, and mass balance is inferred in the liquor by difference. The residual solids after alkaline pretreatment are characterized for crystallinity and imaged by scanning and transmission electron microscopy to reveal the physical changes in the carbohydrate portions of the biomass remaining after pretreatment, which demonstrate dramatic modifications to biomass cell wall architecture with lignin removal but rather insignificant changes in cellulose crystallinity. Our results show that alkaline pretreatment at relatively mild conditions is able to remove substantial amounts of lignin from biomass. Going forward, to be an economically feasibile process, technologies will be required to upgrade the resulting lignin-rich liquor stream.

Alkaline aerobic oxidation is an effective way to produce valuable aromatic chemicals from lignin.

No abstract