No abstract

Here, the researchers carried out an experimental analysis of the effect of the TiO2 nanosolution concentration on the heat transfer of the twin jet impingement on an aluminum plate surface. We used three different heat transfer enhancement processes. We considered the TiO2 nanosolution coat, aluminum plate heat sink, and a twin jet impingement system. We also analyzed several other parameters like the nozzle spacing, nanosolution concentration, and the nozzle-to-plate distance and noted if these parameters could increase the heat transfer rate of the twin jet impingement system on a hot aluminum surface. The researchers prepared different nanosolutions, which consisted of varying concentrations, and coated them on the metal surface. Thereafter, we carried out an X-ray diffraction (XRD) and a Field Emission Scanning Electron Microscopy (FESEM) analysis for determining the structure and the homogeneous surface coating of the nanosolutions. This article also studied the different positions of the twin jets for determining the maximal Nusselt number (Nu). The researchers analyzed all the results and noted that the flow structure of the twin impingement jets at the interference zone was the major issue affecting the increase in the heat transfer rate. The combined influence of the spacing and nanoparticle concentration affected the flow structure, and therefore the heat transfer properties, wherein the Reynolds number (1% by volume concentration) maximally affected the Nusselt number. This improved the performance of various industrial and engineering applications. Hypothesis: Nusselt number was affected by the ratio of the nanoparticle size to the surface roughness. Heat transfer characteristics could be improved if the researchers selected an appropriate impingement system and selected the optimal levels of other factors. The surface coating with the TiO2 nanosolution also positively affected the heat transfer rate.

A CdS thin film buffer layer has been widely used as conventional n-type heterojunction partner both in established and emerging thin film photovoltaic devices. In this study, we perform numerical simulation to elucidate the influence of electrical properties of the CdS buffer layer, essentially in terms of carrier mobility and carrier concentration on the performance of SLG/Mo/p-Absorber/n-CdS/n-ZnO/Ag configured thin film photovoltaic devices, by using the Solar Cell Capacitance Simulator (SCAPS-1D). A wide range of p-type absorber layers with a band gap from 0.9 to 1.7 eV and electron affinity from 3.7 to 4.7 eV have been considered in this simulation study. For an ideal absorber layer (no defect), the carrier mobility and carrier concentration of CdS buffer layer do not significantly alter the maximum attainable efficiency. Generally, it was revealed that for an absorber layer with a conduction band offset (CBO) that is more than 0.3 eV, Jsc is strongly dependent on the carrier mobility and carrier concentration of the CdS buffer layer, whereas Voc is predominantly dependent on the back contact barrier height. However, as the bulk defect density of the absorber layer is increased from 1014 to 1018 cm−3, a CdS buffer layer with higher carrier mobility and carrier concentration is an imperative requirement to a yield device with higher conversion efficiency and a larger band gap-CBO window for realization of a functional device. Most tellingly, simulation outcomes from this study reveal that electrical properties of the CdS buffer layer play a decisive role in determining the progress of emerging p-type photo-absorber layer materials, particularly during the embryonic device development stage.

Antimony trisulfide (Sb2Se3), a non-toxic and accessible substance, has possibilities as a material for use in solar cells. The current study numerically analyses Sb2Se3 solar cells through the program Solar Cell Capacitance Simulator (SCAPS). A detailed simulation and analysis of the influence of the Sb2Se3 layer’s thickness, defect density, band gap, energy level, and carrier concentration on the devices’ performance are carried out. The results indicate that a good device performance is guaranteed with the following values in the Sb2Se3 layer: an 800 optimal thickness for the Sb2Se3 absorber; less than 1015 cm−3 for the absorber defect density; a 1.2 eV optimum band gap; a 0.1 eV energy level (above the valence band); and a 1014 cm−3 carrier concentration. The highest efficiency of 30% can be attained following optimization of diverse parameters. The simulation outcomes offer beneficial insights and directions for designing and engineering Sb2Se3 solar cells.

In this study, we aimed to increase the knowledge regarding the response mechanisms which were associated with the formation of CdS thin films. CdS thin film remains the most appealing alternative for many researchers, as it has been a capable buffer material for effect in film based polycrystalline solar cells (CdTe, CIGSe, CZTS). The Linker Assisted and Chemical Bath Deposition (LA-CBD) technique, which combines the Linker Assisted (LA) technique and the chemical bath deposition (CBD) method for forming high quality CdS thin film, was presented as an efficient and novel hybrid sensitization technique. CdS films were bound to soda lime with the help of electrostatic forces, which led to the formation of the intermediate complexes [Cd (NH3)4]2+ that helped in the collision of these complexes with a soda lime slide. Salvia dye and as a linker molecule 3-Mercaptopropionic acid (MPA) was used in the one step fabrication technique. Optical results showed that the bandgap varied in the range of (2.50 to 2.17) eV. Morphological properties showed a homogeneous distribution of the particles that aspherical in shape in the CdS + MPA + Salvia dye films. This technique significantly affected on the electrical characterizations of CdS films after the annealing process. The CdS + Ag + MPA + Salvia dye films showed the maximum carrier concentration and minimum resistivity, as 5.64 × 10 18 cm−3 and 0.83 Ω cm respectively.