A previous study (Langmuir2011, 27, 5772) found the fluorinated double-tail sulfogulutarate 8FG(EO)(2) to act as a superefficient solubilizer for water in supercritical CO(2) (W/CO(2)) microemulsions. To explore more economic CO(2)-philic surfactants with high solubilizing power as well as rapid solubilization rates, the effects of fluorocarbon chain length and linking group were examined with sodium 1,5-bis(1H,1H,2H,2H-perfluoroalkyloxy)-1,5-dioxopentane-2-sulfonates (nFG(EO)(2), fluorocarbon chain length n = 4, 6, 8) and sodium 1,4-bis(1H,1H,2H,2H-perfluoroalkyloxy)-1,4-dioxobutane-2-sulfonate (nFS(EO)(2), n = 4, 8). Visual observation and UV-vis spectral measurements with methyl orange as a reporter dye indicated a maximum water-to-surfactant molar ratio (W(0)) in the microemulsions, which was 60-80 for nFG(EO)(2) and 40-50 for nFG(EO)(2). Although it is normally expected that high solubilizing power requires long fluorocarbon surfactant chains, the shortest fluorocarbon 4FG(EO)(2) interestingly achieved the highest W(0) (80) transparent single-phase W/CO(2) microemulsion. In addition, a very rapid solubilization of loaded water into CO(2) was observed for 4FG(EO)(2) even at a high W(0) of ~80.

High-pressure small-angle neutron scattering (HP-SANS) studies were conducted to investigate nanostructures and interfacial properties of water-in-supercritical CO2 (W/CO2) microemulsions with double-fluorocarbon-tail anionic surfactants, having different fluorocarbon chain lengths and linking groups (glutarate or succinate). At constant pressure and temperature, the microemulsion aqueous cores were found to swell with an increase in water-to-surfactant ratio, W0, until their solubilizing capacities were reached. Surfactants with fluorocarbon chain lengths of n = 4, 6, and 8 formed spherical reversed micelles in supercritical CO2 even at W0 over the solubilizing powers as determined by phase behavior studies, suggesting formation of Winsor-IV W/CO2 microemulsions and then Winsor-II W/CO2 microemulsions. On the other hand, a short C2 chain fluorocarbon surfactant analogue displayed a transition from Winsor-IV microemulsions to lamellar liquid crystals at W0 =25. Critical packing parameters and aggregation numbers were calculated by using area per head group, shell thickness, the core/shell radii determined from SANS data analysis: these parameters were used to help understand differences in aggregation behavior and solubilizing power in CO2. Increasing the microemulsion water loading led the critical packing parameter to decrease to ~1.3 and the aggregation number to increase to > 90. Although these parameters were comparable between glutarate and succinate surfactants with the same fluorocarbon chain, decreasing the fluorocarbon chain length n reduced the critical packing parameter. At the same time, reducing chain length to 2 reduced negative interfacial curvature, favoring planar structures, as demonstrated by generation of lamellar liquid crystal phases.

A trichain anionic surfactant sodium 1,4-bis(neopentyloxy)-3-(neopentyloxycarbonyl)-1,4-dioxobutane-2-sulfonate (TC14) is shown to aggregate in three different types of solvent: water, heptane, and liquid CO(2). Small-angle neutron scattering (SANS) has been used to characterize the surfactant aggregates in water, heptane, and dense CO(2). Surface tension measurements, and analyses, show that the addition of a third branched chain to the surfactant structural template is critical for sufficiently lowering the surface energy, tipping the balance between a CO(2)-incompatible surfactant (AOT) and CO(2)-philic compounds that will aggregate to form micelles in dense CO(2) (TC14). These results highlight TC14 as one of the most adaptable and useful surfactants discovered to date, being compatible with a wide range of solvent types from high dielectric polar solvent water to alkanes with low dielectrics and even being active in the uncooperative and challenging solvent environment of liquid CO(2).

The article addresses an important, and still unresolved question in the field of CO(2) science and technology: what is the minimum fluorine content necessary to obtain a CO(2)-philic surfactant? A previous publication (Langmuir 2002, 18, 3014) suggested there should be an ideal fluorination level: for optimization of possible process applications in CO(2), it is important to establish just how little F is needed to render a surfactant CO(2)-philic. Here, optimum chemical structures for water-in-CO(2) (w/c) microemulsion stabilization are identified through a systematic study of CO(2)-philic surfactant design based on dichain sulfosuccinates. High pressure small-angle neutron scattering (HP-SANS) measurements of reversed micelle formation in CO(2) show a clear relationship between F content and CO(2) compatibility of any given surfactant. Interestingly, high F content surfactants, having lower limiting aqueous surface tensions, γ(cmc), also have better performance in CO(2), as indicated by lower cloud point pressures, P(trans). The results have important implications for the rational design of CO(2)-philic surfactants helping to identify the most economic and efficient compounds for emerging CO(2) based fluid technologies.