In this study, a spatially stratified proportional fertilizer application device was designed, which was mainly composed of a fertilizer equalization and stirring structure, fertilizer guide plate, and fertilizer plate. This was aimed at solving challenges presented by current fertilizer devices that include a poor layering effect due to untimely return of soil, excess nutrients in the early stages of plant growth, and insufficient quantities in the later stages. The “seed fertilizer + chasing fertilizer” is time-consuming and laborious; seed and fertilizer (without layering) are applied to the soil at once, which tends to cause too much nutrients for plants in the early stage and not enough nutrients in the later stage; and the layered fertilizer machines currently on the market have a poor layering effect due to untimely soil return. Through theoretical analysis and calculation, the structural parameters of the device were determined, and the main influencing factors of the movement law of fertilizer in the device were analyzed. Through simulating soil tank tests, the main factors affecting the effect of fertilizer spatial stratification were designed by quadratic regression orthogonal rotation combination designs. The optimal parameters including the length of the first fertilizer plate was 100 mm, the installation angle of the fertilizer plate was 80°, the spacing of the fertilizer port was 30 mm, and the uniform stirring speed was 650 r/min. The results of the bench test showed that the fertilizer granules could be uniformly stirred at the optimized stirring speed, with average values of 74.56, 76.56, and 105.19 g, which met the agronomic fertilizer application requirements, and the coefficient of variation of fertilizer application amount in each layer was less than 1%. The field test results showed that the stratified proportional fertilizer application device could achieve the stratified proportional application of fertilizer in the soil in ranges of 80.2–95.4, 150.3–180.2, and 230.3–250.4 mm for the upper, middle, and lower layers, respectively, with an error within 10 mm from the designed theoretical application depth. Compared with the conventional fertilizer application method, this fertilizer application method had a more obvious promotion effect on the 100-grain weight and yield of corn.

The flowering characteristics of adzuki bean are influenced by several environmental factors. Light is an important ecological factor that induces flowering in adzuki bean, but to date, there have been few reports on the transcriptomic features of photoperiodic regulation of adzuki bean flowering. This study is based on RNA sequencing (RNA-seq) techniques to elucidate the expression of light-related regulatory genes under short-day photoperiod inducement of adzuki bean flowering, providing an important theoretical basis for its accelerated breeding. Short-day photoperiod inducement of 10 h was conducted for 5 day, 10 day, and 15 day periods on “Tang shan hong xiao dou” varieties, which are more sensitive to short-day photoperiod conditions than the other varieties. Plants grown under natural light (14.5 h) for 5 days, 10 days, and 15 days were used as controls to compare the progress of flower bud differentiation and flowering characteristics. The topmost unfolded functional leaves were selected for transcriptome sequencing and bioinformatics analysis. The short-day photoperiod inducement promoted flower bud differentiation and advanced flowering time in adzuki bean. Transcriptomic analysis revealed 5,608 differentially expressed genes (DEGs) for the combination of CK-5d vs. SD-5d, CK-10d vs. SD-10d, and CK-15d vs. SD-15d. The three groups of the DEGs were analyzed using the Gene Ontology (GO) and the Kyoto Encyclopedia of Genomes and Genomes (KEGG) databases; the DEGs were associated with flowering, photosystem, and the circadian rhythm and were mainly concentrated in the hormone signaling and metabolism, circadian rhythm, and antenna protein pathways; So, 13 light-related genes across the three pathways were screened for differential and expression characteristics. Through the functional annotations of orthologs, these genes were related to flowering, which were supposed to be good candidate genes in adzuki bean. The findings provide a deep understanding of the molecular mechanisms of adzuki bean flowering in response to short-day photoperiod inducement, which laid a foundation for the functional verification of genes in the next step, and provide an important reference for the molecular breeding of adzuki bean.

Water scarcity is a major limiting factor for crop production in North China Plain (NCP), which produces the majority of the country's winter wheat (Triticum aestivum L.). The objective of this three-year field study was to see if and when irrigation one-time in spring improves grain yield and water use efficiency. Four sets of irrigation were established at the 3-leaf visible stage (L3) and the L4, L5, and L6 stages. The spike number, 1,000-grain weight, and water consumption increased progressively when irrigation time was delayed, whereas grain yield, grain number, dry matter, harvest, and WUE grew, then dropped, and peaked at L4. The increased grain number can be attributed to the L4's higher daily water consumption and water consumption percentage than the L3, L5, and L6 at the jointing-anthesis stages. L4 had a shorter cumulative period of soil drought stress (37 days), whereas L3, L5, and L6 had 40, 42, and 43 days, respectively. Furthermore, flag leaf senescence was postponed in L4 with a better post-anthesis leaf area index, photosynthetic rate, chlorophyll content, stronger superoxide dismutase activity, and reduced malondialdehyde concentration. As a result, single irrigation at the 4-leaf visible stage optimized water deficit and consumption before and after anthesis, resulting in higher yield and WUE in the NCP.

Aiming at the problems of low utilization rate of corn fertilizer, low precision of fertilization ratio, and time-consuming and laborious topdressing in the later stage, an U-shaped fertilization device with uniform fertilizer mechanism was designed. The device was mainly composed of uniform fertilizer mixing mechanism, fertilizer guide plate and fertilization plate. Compound fertilizer was applied on both sides and slow/controlled release fertilizer was applied at the bottom to form an U-shaped distribution of fertilizer around corn seeds. Through theoretical analysis and calculation, the structural parameters of the fertilization device were determined. Through the simulated soil tank test, the quadratic regression orthogonal rotation combination design was carried out on the main factors affecting the spatial stratification effect of fertilizer. The optimal parameters were obtained as follows: the stirring speed of the stirring structure was 300 r/min, the bending angle of the fertilization tube was 165°, and the operating speed of the fertilization device was 3 km/h. The results of bench verification test showed that under the optimized stirring speed and bending angle, the fertilizer particles were stirred evenly, and the average values of fertilizer flowing out of the fertilization tubes on both sides were 299.5 g and 297.4 g, respectively. The average fertilizer amounts of the three fertilizer outlets were 200.4 g, 203.2 g and 197.7 g, respectively, which met the agronomic requirements of 1:1:1 fertilization, and the variation coefficients of fertilizer amounts on both sides of the fertilizer pipe and each layer were less than 0.1% and 0.4%, respectively. The simulation results of the optimized U-shaped fertilization device can achieve the expected U-shaped fertilization effect around corn seeds. The results of field experiment showed that the U-shaped fertilization device could realize the U-shaped proportional application of fertilizer in soil. The distance between the upper end of fertilization on both sides and the distance between the base fertilizer and the surface were 87.3 ~ 95.2 mm and 197.8 ~ 206.0 mm, respectively. The transverse distance between the fertilizers on both sides was 84.3 ~ 99.4 mm, and the error with the designed theoretical fertilization was within 10 mm. Compared with the traditional side fertilization method, the number of corn roots increased by 5 ~ 6, the root length increased by 30 ~ 40 mm, and the yield increased by 9.9 ~ 14.8 %.

Aiming at the problems of low utilization rate of corn fertilizer, low precision of fertilization ratio, and time-consuming and laborious topdressing in the later stage, an U-shaped fertilization device with uniform fertilizer mechanism was designed. The device was mainly composed of uniform fertilizer mixing mechanism, fertilizer guide plate and fertilization plate. Compound fertilizer was applied on both sides and slow/controlled release fertilizer was applied at the bottom to form an U-shaped distribution of fertilizer around corn seeds. Through theoretical analysis and calculation, the structural parameters of the fertilization device were determined. Through the simulated soil tank test, the quadratic regression orthogonal rotation combination design was carried out on the main factors affecting the spatial stratification effect of fertilizer. The optimal parameters were obtained as follows: the stirring speed of the stirring structure was 300 r/min, the bending angle of the fertilization tube was 165°, and the operating speed of the fertilization device was 3 km/h. The results of bench verification test showed that under the optimized stirring speed and bending angle, the fertilizer particles were stirred evenly, and the average values of fertilizer flowing out of the fertilization tubes on both sides were 299.5 g and 297.4 g, respectively. The average fertilizer amounts of the three fertilizer outlets were 200.4 g, 203.2 g and 197.7 g, respectively, which met the agronomic requirements of 1:1:1 fertilization, and the variation coefficients of fertilizer amounts on both sides of the fertilizer pipe and each layer were less than 0.1% and 0.4%, respectively. The simulation results of the optimized U-shaped fertilization device can achieve the expected U-shaped fertilization effect around corn seeds. The results of field experiment showed that the U-shaped fertilization device could realize the U-shaped proportional application of fertilizer in soil. The distance between the upper end of fertilization on both sides and the distance between the base fertilizer and the surface were 87.3–95.2 mm and 197.8–206.0 mm, respectively. The transverse distance between the fertilizers on both sides was 84.3–99.4 mm, and the error with the designed theoretical fertilization was within 10 mm. Compared with the traditional side fertilization method, the number of corn roots increased by 5–6, the root length increased by 30–40 mm, and the yield increased by 9.9–14.8%.