A considerable body of research is currently being performed to quantify available tidal energy resources and to develop efficient devices with which to harness them. This work is naturally focussed on maximising power generation from the most promising sites, and a review of the literature suggests that the potential for smaller scale, local tidal power generation from shallow near-shore sites has not yet been investigated. If such generation is feasible, it could have the potential to provide sustainable electricity for coastal homes and communities as part of a distributed generation strategy, and would benefit from easier installation and maintenance, lower cabling and infrastructure requirements and reduced capital costs when compared with larger scale projects. This article reviews tidal barrages and lagoons, tidal turbines, oscillating hydrofoils and tidal kites to assess their suitability for smaller scale electricity generation in the shallower waters of coastal areas at the design stage. This is achieved by discussing the power density, scalability, durability, maintainability, economic potential and environmental impacts of each concept. The discussion suggests that tidal kites and range devices are not well suited toward small-scale shallow water applications due to depth and size requirements, respectively. Cross-flow turbines appear to be the most suitable technology, as they have high power densities and a maximum size that is not constrained by water depth. Oscillating hydrofoils would also be appropriate, provided comparable levels of efficiency can be achieved.

No abstract

a b s t r a c tIn recent years, several papers have been published that investigate the potential use of ionic liquids (ILs) as additives in lubricants. However, corrosive attack of ILs on lubricated metal surfaces and low miscibility of ILs in the non-polar oils are major obstacles to maintaining an optimum lubrication performance level. High miscibility and no corrosive behaviour of Trihexyltetradecyl phosphonium bis(2,4,4-trimethylpentyl) phosphinate and Trihexyltetradecyl phosphonium bis(2-ethylhexyl) phosphate, as lubricating oil additives have recently been described in literature. This article presents work on using these phosphonium based ILs as an additive in the fully formulated diesel engine lubricants. This approach could allow the used lubricants to recover their tribological performance for further use at the end of service life. This extension of service life has the potential to generate significant economic and environmental benefits. Also it will add to the much needed knowledge about the effect of interaction between ILs and existing additives in engine-aged lubricants on the tribological performance of ringliner tribo-system of diesel engines. Results revealed an improvement in friction and antiwear performance of used lubricant by addition of both ILs. However an increase in wear was noted for new (fresh) and in-service lubricant samples. An interesting interference between existing lubricant additives and added ILs in a boundary film formation process has been observed.

It is necessary to use an inclined slipway to launch lifeboats in locations where there is no natural harbour. Slipway stations consist of an initial roller section followed by an inclined keelway, the lifeboat is released from the top of the slipway and proceeds under its own weight into the water. Contact is between the lifeboat keel and a lined, greased keelway and this that determines the friction along the slipway. This paper describes a bench test methodology to investigate this contact. The selection of a modified TE57 reciprocating tribometer and design of a modified pin on plate arrangement is discussed. A test schedule for both the original nickel/chromium coated steel lining and the new low-friction jute fibre/phenolic resin composite lining is developed to accurately reflect real world conditions including environmental contamination such as seawater or wind-blown sand. Environmentally conscious lubricants including water and bio-greases are investigated and compared for their effects in reducing slipway panel friction and wear. Experimental data is collected to establish wear mechanisms, wear volumes and friction characteristics for a range of lubricants and environmental contaminants for the two most common lifeboat keelway lining materials. Implications of this research for future lifeboat slipway design are discussed.

Recently graphene and other 2D materials were suggested as nano additives to enhance the performance of nanolubricants and reducing friction and wear-related failures in moving mechanical parts. Nevertheless, up to our knowledge there are not previous studies on electrochemical exfoliated nanomaterials as lubricant additives. In this work, engine oil-based nanolubricants were developed via two-steps method using two different 2D nanomaterials: a carbon-based nano additive, graphene nanoplatelets (GNP) and a sulphide nanomaterial, molybdenum disulfide (MoS 2 ) nanoplatelets (MSNP). The influence of these nano additives on the thermophysical properties of the nanolubricants, such as viscosity index, density and wettability, was investigated. The unique features of the electrochemical exfoliated GNP and MSNP allow the formulation of nanolubricant with unusual thermophysical properties. Both the viscosity and density of the nanolubricants decreased by increasing the nanoplatelets loading. The effect of the nano additives loading and temperature on the tribological properties of nanolubricants was investigated using two different test configurations: reciprocating ball-on-plate and rotational ball-on-three-pins. The tribological specimens were analysed by Scanning Electron Microscopy (SEM) and 3D profiler in order to evaluate the wear. The results showed significant improvement in the antifriction and anti-wear properties, for the 2Dmaterials-based nanolubricants as compared with the engine oil, using different contact conditions. For the reciprocal friction tests, maximum friction and worn area reductions of 20% and 22% were achieved for the concentrations of 0.10 wt% and 0.20 wt% GNP, respectively. Besides, the best anti-wear performance was found for the nanolubricant containing 0.05 wt% MSNP in rotational configuration test, with reductions of 42% and 60% in the scar width and depth, respectively, with respect to the engine oil.