Fibers of three constitutionally isomeric rigid-rod polymers, produced by polycondensation of 2,6-dichloro-p-phenylenediamine and terephthaloyl dichloride, were spun from nematic solutions and characterized by wide-angle X-ray diffraction (WAXD) measurements and mechanical tests. A post-spin heat treatment was employed to improve the low degrees of orientation and crystallinity that the untreated fibers showed. The dominating crystal structure of constitutionally ordered head-to-head/tail-to-tail fibers seems to be very similar to "Modification 11" of the fibers From poly@-phenyleneterephthalamide) (PPTA), but the fibers do not suffer a comparable structural transformation upon heat treatment. Influences of the constitutional regularity in the chains on the crystal structure, structural order and mechanical properties of the fibers could be observed. Both the observed crystal structure and the experimentally determined mechanical properties agree well with the results of detailed atomistic modeling predictions.
Fibers of three rigid-rod aromatic copolymers, produced by polycondensation of 2,2,6,6-tetraoxo-I ,3,5,7-tetrahydro-2,6-dithia-s-indacene-4,8-diamine (DSDA), p-phenylenedianiine and terephthaloyl dichloride, were spun from nematic solutions and characterized by wideangle X-ray-diffraction (WAXD) measurements and mechanical tests. A post-spin heat treatment was employed to improve the low degrees of orientation and crystallinity exhibited generally by the untreated fibers. The dominating crystal structures of the copolymers are similar to "modification I" of the well known fibers from poly@-phenyleneterephthalamide) (PPTA). Thermally induced crosslinking of the fibers in the solid state was performed simultaneously with post-spin treatment. The influence of the annealing conditions on the mechanical fiber properties and the molecular order in the fibers was also investigated. All mechanical parameters were timedependent, probably due to the generation of stable radicals during heat treatment. The radicals may give rise to chain scission.Poly(pphenyleneterephtha1amide) (PFTA), as a typical representative for rigid-rod polymers, has a tensile strength of 3,4 GPa compared to a compressive strength in the range of 400 MPa2).Different authors have described the typical fiber buckling or formation of kinkbands caused by axial compressive failure3-'). Recent work on the structural and morphological anisotropy of the aramid fibers suggested a stress coupling phenomenon that leads to a dependence of the axial compressive strength on the shear modulus2). The shear modulus in turn has quantitatively been explained in terms of the local, molecular structure for PFTA. The crystal structure is well known3S9-'I). On the molecular level, the fibers consist of hydrogen-bonded planes parallel to the fiber axis. Two adjacent planes are connected only by comparatively weak van der Waals interactions. Rutledge and Suter 13) have calculated the different shear moduli in and perpendicular to these planes by detailed atomistic simulations. This computational approach gives rise to the assumption that a gliding of two adjacent Part I: cf. ref. 14). b,
Two different, novel approaches to crosslink fully aromatic, rigid‐rod aramid chains were studied. First, the new rigid‐rod aramid poly[1,4‐phenylen‐2,5‐bis(prop‐2‐ynyloxy)‐terephthalamide] with an inherent viscosity of ηinh = 2.74 dL/g was synthesized by low temperature polycondensation of p‐phenylendiamine and 2,5‐bis(prop‐2‐ynyloxy)‐terephthaloylchloride. The pendant alkinyl moieties allowed thermally induced crosslinking at temperatures higher than 200°C. No weight loss was found due to this treatment, but curing gave rise to the formation of stable radicals. However, no fiber spinning experiments were carried out using this material due to the insufficient stability of the polymer chains against degradation when being dissolved in sulfuric acid. Furthermore, fibers of a rigid rod polyamide containing pyrimidine moieties, produced by polycondensation of bis‐silylated 2,5‐diaminoprimidine and terephthaloyl dichloride, were spun from nematic solutions. Fibers were crosslinked by complexation with nickel(II)‐ions in the swollen state. Both crosslinked and non‐crosslinked, otherwise identically processed samples, were characterized by wide‐angle X‐ray‐diffraction (WAXD) measurements and mechanical tests. A post‐spin heat treatment was employed to improve the low degrees of orientation and crystallinity that the untreated fibers in general showed. The dominating crystal structures of both fiber samples are similar to “Modification II” of the well characterized fibers from poly(p‐phenylene‐terephthalamide) (PPTA). The number and size of the morphological defects in the crosslinked fibers was significantly higher than in the non‐crosslinked samples. The influence of the annealing on the mechanical fiber properties and the molecular order in the fibers was investigated. The values of all mechanical parameters were considerably lower in the case of the crosslinked fibers, probably due to the collapse of the entire supramolecular order and fiber morphology.
2',5'-Diamino-4-(dimethylamino)-4'-nitrostilbene was polymerized with terephthaloyl dichloride and 2,6-difluoroterephthaloyl dichloride in a low-temperature solution polycondensation to give two novel, fully aromatic rigid-rod polyamides. Nematic solutions of these polymers were processed into fibers and films that were characterized by wide-angle X-ray diffraction measurements. A post-spin annealing process was employed to enhance the chain orientation in the fibers. The dominating crystal structure was found to be similar to "modification 11" of the fibers from poly@-phenyleneterephthalamide), but the fibers do not suffer a comparable structural transformation upon heat treatment. A corona-discharge poling process gave rise to a remarkable gain in average chain orientation in the films. Again the crystal structure was found to be similar to "modification 11". The aramids investigated in this work represent a new approach to the design of liquid-crystalline rigid-rod polymers, where different mechanisms of orientation can be combined. In the nematic phase, the rigid-rod molecules form highly oriented domains that can be oriented using mechanical processes such as shearing. In addition the stilbene units that are fixed in the polymer backbone with their dipole moments oriented transverse to the main chain can be oriented in an electric field. The combination of both orientation mechanisms seems to cause a synergistic effect, probably since each affects different levels of the polymer microstructure in the solid.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.