Severe plastic deformation Compositionally complex alloys 3 dimensional atom probe tomography Microstructure a b s t r a c t An equiatomic CoCrFeMnNi high-entropy alloy (HEA), produced by arc melting and drop casting, was subjected to severe plastic deformation (SPD) using high-pressure torsion. This process induced substantial grain refinement in the coarse-grained casting leading to a grain size of approximately 50 nm. As a result, strength increased significantly to 1950 MPa, and hardness to 520 HV. Analyses using transmission electron microscopy (TEM) and 3-dimensional atom probe tomography (3D-APT) showed that, after SPD, the alloy remained a true single-phase solid solution down to the atomic scale. Subsequent investigations characterized the evolution of mechanical properties and microstructure of this nanocrystalline HEA upon annealing. Isochronal (for 1 h) and isothermal heat treatments were performed followed by microhardness and tensile tests. The isochronal anneals led to a marked hardness increase with a maximum hardness of 630 HV at about 450°C before softening set in at higher temperatures. The isothermal anneals, performed at this peak hardness temperature, revealed an additional hardness rise to a maximum of about 910 HV after 100 h. To clarify this unexpected annealing response, comprehensive microstructural analyses were performed using TEM and 3D-APT. New nano-scale phases were observed to form in the originally single-phase HEA. After times as short as 5 min at 450°C, a NiMn phase and Cr-rich phase formed. With increasing annealing time, their volume fractions increased and a third phase, FeCo, also formed. It appears that the surfeit of grain boundaries in the nanocrystalline HEA offer many fast diffusion pathways and nucleation sites to facilitate this phase decomposition. The hardness increase, especially for the longer annealing times, can be attributed to these nano-scaled phases embedded in the HEA matrix. The present results give new valuable insights into the phase stability of single-phase high-entropy alloys as well as the mechanisms controlling the mechanical properties of nanostructured multiphase composites.

No abstract

No abstract

11Beta-hydroxysteroid dehydrogenase type 1 (11beta-HSD 1) is a microsomal enzyme that catalyzes the reversible interconversion of receptor-active 11-hydroxy glucocorticoids (cortisol) to their receptor-inactive 11-oxo metabolites (cortisone). However, the physiological role of 11beta-HSD 1 as prereceptor control device in regulating access of glucocorticoid hormones to the glucocorticoid receptor remains obscure in light of its low substrate affinities, which is in contrast to low glucocorticoid plasma levels and low Kd values of the receptors to cortisol. To solve this enigma, we performed detailed kinetic analyses with a homogeneously purified 11beta-HSD 1 from human liver. The membrane-bound enzyme was successfully obtained in an active state by a purification procedure that took advantage of a gentle solubilization method as well as providing a favorable detergent surrounding during the various chromatographic steps. The identity of purified 11beta-HSD 1 was proven by determination of enzymatic activity, N-terminal amino acid sequencing, and immunoblot analysis. By gel-permeation chromatography we could demonstrate that 11beta-HSD 1 is active as a dimeric enzyme. The cDNA for the enzyme was cloned from a human liver cDNA library and shown to be homologous to that previously characterized in human testis. Interestingly, 11beta-HSD 1 exhibits Michaelis-Menten kinetics with cortisol and corticosterone (11beta-dehydrogenation activity) but cooperative kinetics with cortisone and dehydrocorticosterone (11-oxoreducing activity). Accordingly, this enzyme dynamically adapts to low (nanomolar) as well as to high (micromolar) substrate concentrations, thereby providing the fine-tuning required as a consequence of great variations in circadian plasma glucocorticoid levels.

Structural materials used for safety critical applications require high strength and simultaneously high resistance against crack growth, referred to as damage tolerance. However, the two properties typically exclude each other and research efforts towards ever stronger materials are hampered by drastic loss of fracture resistance. Therefore, future development of novel ultra-strong bulk materials requires a fundamental understanding of the toughness determining mechanisms. As model material we use today’s strongest metallic bulk material, namely, a nanostructured pearlitic steel wire, and measured the fracture toughness on micron-sized specimens in different crack growth directions and found an unexpected strong anisotropy in the fracture resistance. Along the wire axis the material reveals ultra-high strength combined with so far unprecedented damage tolerance. We attribute this excellent property combination to the anisotropy in the fracture toughness inducing a high propensity for micro-crack formation parallel to the wire axis. This effect causes a local crack tip stress relaxation and enables the high fracture toughness without being detrimental to the material’s strength.