The addition of refractory metals represents a promising approach for development of future high-entropy alloys (HEAs). Niobium and molybdenum are particularly suitable additives for increasing hardness as well as wear and corrosion resistance. In the context of surface protection applications, eutectic high-entropy alloys (EHEAs) with their homogeneous property profile are of specific interest. In the present work, two EHEAs were developed starting from the alloy Al0.3CoCrFeNi using electric arc melting. Following mechanical and microstructural characterization, the two alloys were found to have the compositions Al0.3CoCrFeNiMo0.75 and Al0.3CoCrFeNiNb0.5. For thermal spray processing, powders of the above alloys were prepared by inert gas atomization. The coatings produced by high-velocity oxy-fuel spraying (HVOF) were characterized and evaluated compared with castings, allowing process–structure–property relationships to be derived. Based on the results, statements on possible application potential can be made.

No abstract

Compositional alterations to high-entropy alloys (HEAs) allow further evolution of these materials by adjusting their property profiles. This way, they can be used for coating technologies and surface-protection applications. In the present work, minor quantities of the non-metallic alloying constituents, BSiC, were added to the CrFeNi base system. The alloy development was carried out in an electric arc furnace in comparison with the nickel-based alloy Ni-600. With regard to the BSiC-free variant, the wear resistance can be significantly increased. The powder was manufactured by inert gas atomization and characterized, followed by processing via high-velocity oxy-fuel spraying (HVOF) and high velocity laser metal deposition (HS-LMD). Depending on the manufacturing conditions, the proportion and shape of the precipitates within the microstructure differ. Compared to both the reference system and the as-cast condition, the coating systems demonstrated comparable or improved resistance to wear. The evaluation of the process–structure–property relationships confirmed the great potential of developing load-adapted HEA systems using non-metallic alloy constituents in the field of surface engineering.

Self-fluxing alloys are an established thermal spray system in case of superimposed tribological and corrosive loads. A dense coating with high bonding strength can be formed by fusing. Such coating system represent the state of the art in valve technology. Diamond-like carbon (DLC) top coatings are used for friction-reduction. As an alternative approach, this study focuses on the possibility of incorporating solid lubricants in self-fluxing alloy coatings. This allows for higher local stress and failure tolerance as well as a reduced process chain. Molybdenum disulfide (MoS2) was studied as solid lubricant in the self-fluxing alloy NiCrBSiFe. In this preliminary study, the optimization of the MoS2 content with up to 10.0 wt% was performed in spark plasma sintered (SPS) bulk materials. The wear behavior under oscillating wear conditions was investigated. Besides the decrease in coefficient of friction (COF), the wear resistance was increased by incorporating MoS2. Furthermore, the distribution of the solid lubricants within the SPS bulk material and the influence of the production route were analyzed.

In particular, eutectic HEAs (EHEAs) are of interest for coating technology. The microstructure of these multiphase systems is determined by the cooling conditions during solidification and the heat treatment condition. High cooling rates can suppress segregation and allow the formation of a supersaturated solid solution microstructure. Therefore, the property profile differs from that of the equilibrium state. The effect of cooling conditions on the functional properties of EHEA coatings has not been investigated so far. In the current study, the microstructure formation and wear resistance of the metastable EHEA Al0.3CoCrFeNiMo0.75 was investigated. Laser metal deposition (LMD) of the inert gas atomized powder forms a directional vertically solidified lamellar structure. A supersaturated solid solution and a metastable BCC and HCP phase was formed. The microstructure resembles a Widmanstätten structure. By spark plasma sintering (SPS), a statistically distributed orientation of the fine lamellae was produced. The highest microhardness and oscillating wear resistance were detected for the ultrafine LMD coating. By increase of the microstructure domain size, the hardness and oscillating wear resistance decrease. This study reveals the great potential of supersaturated solid solutions of ultrafine EHEAs obtained by LMD processing with high cooling rates.