This work presents the results of the electron-beam welding of commercially pure α-Ti (CP-Ti) and Ti6Al4V (Ti64) alloys. The structure and mechanical properties of the formed welded joints were examined as a function of the power of the electron beam. The beam power was set to P1 = 2100 W, P2 = 1500 W, and P3 = 900 W, respectively. X-ray diffraction (XRD) experiments were performed in order to investigate the phase composition of the fabricated welded joints. The microstructure was examined by both optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). The mechanical properties of the formed joints were studied using tensile test experiments and microhardness experiments. The results of the experiments were discussed concerning the influence of the beam power on the microstructure and the mechanical properties of the weld joints. Furthermore, the practical applicability of the present method for the welding of α-Ti and Ti64 was also discussed.

In this study, we present the results of electron-beam welding of joints with 304-L stainless steel and copper. The influence of the beam’s power on the structures and mechanical properties of the welded joints was studied; the experiments were realized at a beam deflection of 0.3 mm to the Cu plate and beam powers of 2400, 3000, and 3600 W. The phase compositions of the obtained welded joints were studied by using X-ray diffraction (XRD); the microstructure and chemical composition were investigated by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX), respectively. The mechanical properties were studied by using tensile experiments and microhardness investigations. The phase compositions of the welded joints were in the forms of substitutional solid solutions between Fe, Cu, and pure copper and remained unchanged in terms of power. It was found that the microstructures changed gradually with the application of different values of the power of the electron beam. The results of the tensile tests showed higher tensile strengths at lower beam powers (i.e., 2400 and 3000 W) that dropped at 3600 W. The relative elongations rose with increases in the power of the electron beam. Moreover, it was found that the microhardnesses strongly depended on the applied technological conditions (defined by the electron beam’s power) and the corresponding microstructures of the welded joints.

In this study, we present the results from electron-beam welding operations applied on copper and Al6082T6 aluminum alloys. The influence of beam-scanning geometries on the structure and mechanical properties of the welded joint is studied. The experiments were conducted using a circle oscillation mode with an oscillation radius of 0.1 mm and 0.2 mm. The beam deflection was set to 0.4 mm with respect to the side of the aluminum alloy, and the beam power was set at 2700 W. The phase composition of the obtained welded joints was studied by X-ray diffraction (XRD). Scanning electron microscopy (SEM) was used for the investigation of the microstructure of the joints. The chemical composition was investigated by using energy-dispersive X-ray spectroscopy (EDX). The mechanical properties were studied by micro-hardness investigations. The fusion zone of the weld seam contains three phases—an aluminum matrix, an ordered solid solution of copper and aluminum in the form of CuAl2, and pure copper. Electron beam-scanning geometries have significant influences on the structure of the weld. Increasing the beam oscillation’s radius leads to a decrease in intermetallic phases and improves homogeneity. The measured microhardness values in the fusion zone are much higher than the ones measured in the base metals due to the formation of intermetallic phases. The microhardness of the weld joint formed using an oscillation radius of 0.2 mm was much lower compared to the one formed using an oscillation radius of 0.1 mm.

This paper aims to investigate the impact of beam deflection geometry on the structure, surface architecture, and friction coefficient of electron-beam-modified TC4 titanium alloys. During the experiments, the electron beam was deflected in the form of different scanning geometries, namely linear, circular, and matrix. The structure of the treated specimens was investigated in terms of their phase composition by employing X-ray diffraction experiments. The microstructure was studied by scanning electron microscopy (SEM). The surface architecture was examined by atomic force microscopy (AFM). The friction coefficient was studied by a mechanical wear test. It was found that the linear and circular deflection geometries lead to a transformation of the phase composition, from double-phase α + β to α’ martensitic structure. The application of a linear manner of scanning leads to a residual amount of beta phase. The use of a matrix does not tend to structural changes on the surface of the TC4 alloy. In the case of linear geometry, the thickness of the modified zone is more than 800 μm while, in the case of EBSM using circular scanning, the thickness is about 160 μm. The electron-beam surface modification leads to a decrease in the surface roughness to about 27 nm in EBSM with linear deflection geometry and 31 nm in circular deflection geometry, compared to that of the pure TC4 substrate (about 160 nm). The electron-beam surface modification of the TC4 alloy leads to a decrease in the coefficient of friction (COF), with the lowest COF values obtained in the case of linear deflection geometry (0.32). The results obtained in this study show that beam deflection geometry has a significant effect on the surface roughness and friction coefficient of the treated surfaces. It was found that the application of a linear manner of scanning leads to the formation of a surface with the lowest roughness and friction coefficient.

We present the results of an investigation of the structure and mechanical properties of dissimilar joints of copper and 304L stainless steel formed by electron-beam welding. The samples studied were welded without a beam offset and with a beam offset towards either welded materials to a distance of 0.3 mm. The phase composition was determined via X-ray analysis. The structure was investigated using scanning electron microscopy. The mechanical properties, including hardness and tensile strength, were measured. The phase composition of the considered specimens consisted of a double-phase structure of face-centered cubic (fcc) and body-centered cubic (bcc) phases. The sample welded without offset exhibited the highest yield strength and tensile strength values. The microhardness of all samples increased in the fusion zone on the steel side and decreased in the fusion zone on the copper side compared to the initial hardness of the two materials.