Chitin, a linear polysaccharide composed of (134)-linked 2-acetamido-2-deoxy-␤-D-glucopyranose (GlcNAc) residues, and chitosan, the fully or partially N-acetylated, water-soluble derivative of chitin composed of (134)-linked GlcNAc and 2-amino-2-deoxy-␤-D-glucopyranose (GlcN), have been proposed as elicitors of defense reactions in higher plants. We tested and compared the ability of purified (134)-linked oligomers of GlcNAc (tetramer to decamer) and of GlcN (pentamer and heptamer) and partially N-acetylated chitosans with degrees of acetylation (DA) of 1%, 15%, 35%, 49%, and 60% and average degrees of polymerization between 540 and 1100 to elicit phenylalanine ammonia-lyase (PAL) and peroxidase (POD) activities, lignin deposition, and microscopically and macroscopically visible necroses when injected into the intercellular spaces of healthy, nonwounded wheat (Triticum aestivum L.) leaves. Purified oligomers of (134)-linked GlcN were not active as elicitors, whereas purified oligomers of (134)-linked GlcNAc with a degree of polymerization > 7 strongly elicited POD activities but not PAL activities. Partially N-acetylated, polymeric chitosans elicited both PAL and POD activities, and maximum elicitation was observed with chitosans of intermediate DAs. All chitosans but not the chitin oligomers induced the deposition of lignin, the appearance of necrotic cells exhibiting yellow autofluorescence under ultraviolet light, and macroscopically visible necroses; those with intermediate DAs were most active. These results suggest that different mechanisms are involved in the elicitation of POD activities by GlcNAc oligomers, and of PAL and POD activities by partially N-acetylated chitosan polymers and that both enzymes have to be activated for lignin biosynthesis and ensuing necrosis to occur.

Summary• Conversion of surface-exposed chitin to chitosan in cell walls of in vitro -and in vivo -differentiated infection structures of two rust fungi, the wheat stem rust fungus Puccinia graminis f. sp. tritici and the broad bean rust fungus Uromyces fabae , and of the causal agent of maize anthracnose, Colletotrichum graminicola , were studied.• Epi-fluorescence microscopy with the fluorescence-labeled lectin wheat germ agglutinin (WGA) revealed that surfaces of infection structures formed on the plant cuticle expose chitin, whereas surfaces of structures formed after invading the host do not.• To identify chitin modification by de-N -acetylation, we raised polyclonal antibodies specifically recognizing de-N -acetylated chitosan. These antibodies labeled only those infection structures that differentiate inside the plant, indicating that chitosan is exposed on cell wall surfaces post penetration.• Surface modification of the fungal cell walls by chitin de-N -acetylation is discussed as a fungal strategy to protect cell walls of pathogenic hyphae from enzymatic hydrolysis by host chitinases, and to avoid generation of an auto-catalytic defense response system in the invaded host tissue.

Chitosan nanoparticles, produced by ionic gelation, are among the most intensely studied nanosystems for drug delivery. However, a lack of inter-laboratory reproducibility and a poor physicochemical understanding of the process of particle formation have been slowing their potential market applications. To address these shortcomings, the current study presents a systematic analysis of the main polymer factors affecting the nanoparticle formation driven by an initial screening using systematic statistical Design of Experiments (DoE). In summary, we found that for a given chitosan to TPP molar ratio, the average hydrodynamic diameter of the particles formed is strongly dependent on the initial chitosan concentration. The degree of acetylation of the chitosan was found to be the second most important factor involved in the system’s ability to form particles. Interestingly, viscosimetry studies indicated that the particle formation and the average hydrodynamic diameter of the particles formed were highly dependent on the presence or absence of salts in the medium. In conclusion, we found that by controlling two simple factors of the polymer solution, namely its initial concentration and its solvent environment, it is feasible to control in a reproducible manner the production and characteristics of chitosan particles ranging in size from nano- to micrometres.